MID49 3 pin XLR Power Cable for RED V-Raptor XL SKU: M49-CBL-3XR-120 3 pin XLR male connector to 4 pin power cable for RED V-Raptor XL. For use with 24V block batteries or 24V power stations.Weight: 220gDimensions (WxLxH): 20 x 3048 x 6mm

MID49 4 pin XLR Power Cable for ARRI Alexa SKU: M49-CBL-4XA-120 4 pin XLR male connector to 8 pin power cable for ARRI Alexa 35, Alexa Mini, Alexa Mini LF. Product Weight: 220gProduct Dimensions (WxLxH): 20 x 3048 x 6mm

MID49 4 pin XLR Power Cable for RED SKU: M49-CBL-4XR-120 4 pin XLR male connector to 6 pin power cable for RED Komodo-X, V-Raptor, DSMC1, DSMC2. Product Weight: 320gProduct Dimensions (WxLxH): 20 x 3048 x 6mm

MID49 Mains Power Supply 24V (RED V-Raptor XL) SKU: M49-PWS-REDXL-EU Mains Power Supply 24V for the RED V-Raptor XL camera, which provides up to 9A and accepts 120V or 240V AC input. Product Weight: 1023gAC cord length: (WxLxH): 1245mmOutput cord length: (WxLxH): 6 x 1219 x 12mmOverall length: (WxLxH): 82 x 2464 x 62mm

MID49 Power Distribution Box DB-1 (RED Komodo-X / V-Raptor, V-Mount)Power Distribution Box DB-1 (RED Komodo-X / V-Raptor, V-Mount) attaches to the V-Mount interface on the back of the camera and provides intelligent power distribution withD-Taps5V USB-C PD3pin Fischers2pin LEMO compatible connectors9pin EXT cable enables remote start/stop capability using 3pin Fischer devices.Configure the DB-1 in "high mode" which moves the distro box up so that it is flush with the bottom of the camera or in "low mode" where the box is flush with the top of the camera.Move the rod bracket to the bottom of the DB-1 to configure with pass-through rods and mount it further behind the camera as desired. Adjust the distance to the camera body by unlocking the thumbscrew and moving the power plate in and out. 40mm rod extensions are also included for spacing the DB-1 even further from the camera body. Deadlock bracket is included for permanently affixing the V-Mount interface to the camera body.Also available in a 15mm LW Rod Mount only version if direct camera mounting is not required. Hot-swap between on-board battery and 6pin LEMO-style connector without losing camera or accessory power.When both sources are connected, the DC INPUT takes priority down to 12.5V, at which point, the DB-1 will switch to an onboard battery. The DB-1 can also be separated from its camera mount, revealing a 15mm LW rod clamp that can be attached to regular 15mm rods with lightweight spacing (60mm apart, center to center).With the SMART FUSE design, camera power is monitored, and the remaining power budget is allocated to accessories. For example, the camera with 7in touchscreen uses approximately 3.0A at 14V so when using a 10A capable battery, the remaining 7.0A is allocated for accessory use. If an accessory configuration exceeds the 7.0A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 7.0A, the RESET button can be pressed, and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.User changeable Gold Mount Plates available as well.NPUTSBATT: V-Mount plate DC IN: 6pin LEMO-style connector (11-17V) OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock) 1x 9pin EXT (pass thru from camera)

MID49 Power Distribution Box DB-1 (RED Komodo-X / V-Raptor, V-Mount)Power Distribution Box DB-1 (RED Komodo-X / V-Raptor, V-Mount) attaches to the V-Mount interface on the back of the camera and provides intelligent power distribution withD-Taps5V USB-C PD3pin Fischers2pin LEMO compatible connectors9pin EXT cable enables remote start/stop capability using 3pin Fischer devices.Configure the DB-1 in "high mode" which moves the distro box up so that it is flush with the bottom of the camera or in "low mode" where the box is flush with the top of the camera.Move the rod bracket to the bottom of the DB-1 to configure with pass-through rods and mount it further behind the camera as desired. Adjust the distance to the camera body by unlocking the thumbscrew and moving the power plate in and out. 40mm rod extensions are also included for spacing the DB-1 even further from the camera body. Deadlock bracket is included for permanently affixing the V-Mount interface to the camera body.Also available in a 15mm LW Rod Mount only version if direct camera mounting is not required. Hot-swap between on-board battery and 6pin LEMO-style connector without losing camera or accessory power.When both sources are connected, the DC INPUT takes priority down to 12.5V, at which point, the DB-1 will switch to an onboard battery. The DB-1 can also be separated from its camera mount, revealing a 15mm LW rod clamp that can be attached to regular 15mm rods with lightweight spacing (60mm apart, center to center).With the SMART FUSE design, camera power is monitored, and the remaining power budget is allocated to accessories. For example, the camera with 7in touchscreen uses approximately 3.0A at 14V so when using a 10A capable battery, the remaining 7.0A is allocated for accessory use. If an accessory configuration exceeds the 7.0A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 7.0A, the RESET button can be pressed, and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.User changeable Gold Mount Plates available as well.NPUTSBATT: V-Mount plate DC IN: 6pin LEMO-style connector (11-17V) OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock) 1x 9pin EXT (pass thru from camera)

MID49 Power Distribution Box DB-10 (Canon C400)Power Distribution Box DB-10 (Canon C400) attaches to the back of the camera using the included ARCA Backpack and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors.Removable REMOTE LANC cable enables remote start/stop capability using 3pin Fischer devices. Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-8 will switch to an onboard battery.The ARCA Backpack design allows Canon's BP-A30N battery to be installed in the camera to function as an emergency backup. To swap the internal battery, unlock the ARCA Backpack thumbscrew, slide up, and release the battery.With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the C400 uses approximately 1.6A at 14V so when using a 10A capable battery, the remaining 8.4A is allocated for accessory use. If an accessory configuration exceeds the 8.4A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate showing the error and once the configuration has been adjusted to lower than 8.4A, the RESET button can be pressed and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.The DB-10 is also compatible with Canon C300mkIII and Canon C500mkII start/stop capability requires a longer REMOTE LANC cable.INPUTSBATT V-Mount plate / Gold Mount PlateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-10 (Canon C400)Power Distribution Box DB-10 (Canon C400) attaches to the back of the camera using the included ARCA Backpack and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors.Removable REMOTE LANC cable enables remote start/stop capability using 3pin Fischer devices. Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-8 will switch to an onboard battery.The ARCA Backpack design allows Canon's BP-A30N battery to be installed in the camera to function as an emergency backup. To swap the internal battery, unlock the ARCA Backpack thumbscrew, slide up, and release the battery.With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the C400 uses approximately 1.6A at 14V so when using a 10A capable battery, the remaining 8.4A is allocated for accessory use. If an accessory configuration exceeds the 8.4A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate showing the error and once the configuration has been adjusted to lower than 8.4A, the RESET button can be pressed and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.The DB-10 is also compatible with Canon C300mkIII and Canon C500mkII start/stop capability requires a longer REMOTE LANC cable.INPUTSBATT V-Mount plate / Gold Mount PlateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-11 (Sony FX6, V-Mount)Power Distribution Box DB-11 (Sony FX6, V-Mount) attaches directly to the rear two 1/4-20s of the camera body and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors.Removable REMOTE LANC cable enables remote start/stop capability using 3pin Fischer devices. Also available in a hinged 15mm LW Rod Mount version for attaching further away from the camera. Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery.The mount design allows for a Sony BP-U battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-11 up and release the battery. Note that the DB-11 provides 19.5V to the camera so that the camera will default to the DC input.The DB-11 can also be separated from its camera mount, revealing a 15mm rod clamp with an internal friction sleeve. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the FX6 uses approximately 1.0A at 14V so when using a 10A capable battery, the remaining 9.0A is allocated for accessory use. If an accessory configuration exceeds the 9.0A limit, accessory power is cut off, leaving the camera powered.The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 9.0A, the RESET button can be pressed, and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed. The DB-11 is also compatible with Sony FX9, but that camera's mounting points are in a different location so the Rod Mounted version is suggested.User changeable Gold Mount Plates available as well.INPUTSBATT V-Mount plateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-11 (Sony FX6, V-Mount)Power Distribution Box DB-11 (Sony FX6, V-Mount) attaches directly to the rear two 1/4-20s of the camera body and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors.Removable REMOTE LANC cable enables remote start/stop capability using 3pin Fischer devices. Also available in a hinged 15mm LW Rod Mount version for attaching further away from the camera. Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery.The mount design allows for a Sony BP-U battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-11 up and release the battery. Note that the DB-11 provides 19.5V to the camera so that the camera will default to the DC input.The DB-11 can also be separated from its camera mount, revealing a 15mm rod clamp with an internal friction sleeve. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the FX6 uses approximately 1.0A at 14V so when using a 10A capable battery, the remaining 9.0A is allocated for accessory use. If an accessory configuration exceeds the 9.0A limit, accessory power is cut off, leaving the camera powered.The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 9.0A, the RESET button can be pressed, and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed. The DB-11 is also compatible with Sony FX9, but that camera's mounting points are in a different location so the Rod Mounted version is suggested.User changeable Gold Mount Plates available as well.INPUTSBATT V-Mount plateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-12 (URSA Cine, B-Mount)SKU: M49-DB12-BPower Distribution Box DB-12 (Blackmagic URSA Cine, B-Mount) attaches directly to the camera body using five M3 screws and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors.The included USB-C cable can be installed inside DB-12 and connected to the top-rear port on the camera body to enable remote start/stop capability using 3-pin Fischer devices. Hot-swap between on-board battery and 8pin LEMO compatible connector without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 22.8V at which point, the DB-12 will switch to an onboard battery.With the SMART FUSE design, camera power is monitored, and the remaining power budget is allocated to accessories. For example, the URSA Cine uses approximately 4.8A at 28V, so when using a 10A capable battery, the remaining 5.2A is allocated for accessory use. If an accessory configuration exceeds the 5.2A limit, accessory power is cut off, leaving the camera powered.The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 5.2A, the RESET button can be pressed, and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.INPUTSBATT: B-Mount PlateDC IN: 8pin (21-34V)OUTPUTS2x D-Tap (15V regulated)2x 3pin (battery voltage with run/stop)2x 2pin (15V regulated)1x USB-C PD (5V at 3A with thread lock) Also available in a Gold Mount and V-Mount versionsCOMPATIBLE CAMERA MODELSURSA Cine 12K LFURSA Cine 17K 65URSA Cine ImmersiveCOMPATIBLE BATTERIESThis product is compatible with any B-Mount battery capable of 28VINCOMPATIBLE BATTERIESStandard 14.4V batteries will NOT power the camera system. Note that the CORE Maverick Block Battery uses a voltage boost converter to get to 28V and introduces an immense amount of noise into the system, so much so that the DB-12 cannot validate it as a reliable source while an on-board battery is connected. Maverick batteries can only be used when it is the first power source connected.MV6 Core SWX Maverick Block Battery

MID49 Power Distribution Box DB-12 (Blackmagic URSA Cine, V-Mount High Voltage)Power Distribution Box DB-12 (Blackmagic URSA Cine, V-Mount High Voltage) attaches directly to the camera body using five M3 screws and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors.The included USB-C cable can be installed inside DB-12 and connected to the top-rear port on the camera body to enable remote start/stop capability using 3-pin Fischer devices. =Hot-swap between on-board battery and 8pin LEMO compatible connector without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 22.8V at which point, the DB-12 will switch to an onboard battery.With the SMART FUSE design, camera power is monitored, and the remaining power budget is allocated to accessories. For example, the URSA Cine uses approximately 4.8A at 28V, so when using a 10A capable battery, the remaining 5.2A is allocated for accessory use. If an accessory configuration exceeds the 5.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 5.2A, the RESET button can be pressed, and power will be re-enabled to accessory outputs.In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.INPUTSBATT V-Mount High Voltage PlateDC IN 8pin (21-34V)OUTPUTS2x D-Tap (15V regulated)2x 3pin (battery voltage with run/stop)2x 2pin (15V regulated)1x USB-C PD (5V at 3A with thread lock)Also available in a Gold Mount and B-Mount versions.COMPATIBLE CAMERA MODELSURSA Cine 12K LFURSA Cine 17K 65URSA Cine ImmersiveCOMPATIBLE BATTERIESThis product is only compatible with newer Core HIGH VOLTAGE V-Mount batteries, which are listed below and have a current rating of 10A at 28V.HLX-9MXS Core SWX Helix Max 98WhHLX-150MXS Core SWX Helix Max 147WhHLX-275MXV Core SWX Helix Max 275HLX-360MXV Core SWX Helix Max 360HLX-99UMXV Core SWX Helix Max Ultra 99WhHLX-160UMXV Core SWX Helix Max Ultra 156WhHLX-300UMXV Core SWX Helix Max Ultra 297WhHLX-400UMXV Core SWX Helix Max Ultra 395WhAPX-360HV Core SWX APEX 360 High Voltage

MID49 Power Distribution Box DB-13 (FUJIFILM GFX ETERNA 55, V-Mount)SKU: M49-DB13-V Power Distribution Box DB-13 (FUJIFILM GFX ETERNA 55, V-Mount) attaches directly to the back of the camera body using the V-Mount interface to provide intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable LANC cable enables remote start/stop capability using 3pin Fischer devices. Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-13 will switch to an onboard battery.With the SMART FUSE design, camera power is monitored, and the remaining power budget is allocated to accessories. For example, the ETERNA uses approximately 2.0A at 14V so when using a 10A capable battery, the remaining 8.0A is allocated for accessory use. If an accessory configuration exceeds the 8.0 limit, accessory power is cut off, leaving the camera powered.The "SMART FUSE" LED will illuminate showing the error and once the configuration has been adjusted to lower than 8.0A, the RESET button can be pressed and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.INPUTSBATT: V-Mount plate with SMBus communicationDC IN: 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop) 2x 2pin (battery voltage) 1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-4 (Canon C80, V-Mount)Power Distribution Box DB-4 (Canon C80, V-Mount) attaches directly to the shoe mount of the C80 using locking pins and pressure and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable REMOTE LANC cable enables remote start/stop capability using 3pin Fischer devices.Also available in a hinged 15mm LW Rod Mount version for attaching further away from the camera.Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery. The shoe mount design allows Canon's BP-A30N battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-4 up and release the battery. Note that the DB-4 provides 19.5V to the camera so that the camera will default to the DC input.The DB-4 can also be separated from its shoe mount, revealing a 15mm rod clamp with an internal friction sleeve. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the C80 uses approximately 1.0A at 14V so when using a 10A capable battery, the remaining 9.0A is allocated for accessory use. If an accessory configuration exceeds the 9.0A limit, accessory power is cut off, leaving the camera powered.The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 9.0A, the RESET button can be pressed, and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.The DB-4 is also compatible with Canon C70 but that camera's shoe is in a different location so the Rod Mounted version is suggested. User changeable Gold Mount Plates are available as well.INPUTSBATT V-Mount plateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-4 (Canon C80, V-Mount)Power Distribution Box DB-4 (Canon C80, V-Mount) attaches directly to the shoe mount of the C80 using locking pins and pressure and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable REMOTE LANC cable enables remote start/stop capability using 3pin Fischer devices.Also available in a hinged 15mm LW Rod Mount version for attaching further away from the camera.Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery. The shoe mount design allows Canon's BP-A30N battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-4 up and release the battery. Note that the DB-4 provides 19.5V to the camera so that the camera will default to the DC input.The DB-4 can also be separated from its shoe mount, revealing a 15mm rod clamp with an internal friction sleeve. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the C80 uses approximately 1.0A at 14V so when using a 10A capable battery, the remaining 9.0A is allocated for accessory use. If an accessory configuration exceeds the 9.0A limit, accessory power is cut off, leaving the camera powered.The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 9.0A, the RESET button can be pressed, and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.The DB-4 is also compatible with Canon C70 but that camera's shoe is in a different location so the Rod Mounted version is suggested. User changeable Gold Mount Plates are available as well.INPUTSBATT V-Mount plateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-8 (Sony Burano, Gold Mount) Power Distribution Box DB-8 (Sony Burano, Gold Mount) attaches directly to the back of the camera body using the V-Mount interface to provide intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable LANC cable enables remote start/stop capability using 3pin Fischer devices. When using communicative batteries, data is converted to SMBus and sent to the camera enabling percentage data on the monitor. Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-8 will switch to an onboard battery. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the Burano uses approximately 2.8A at 14V so when using a 10A capable battery, the remaining 6.2A is allocated for accessory use. If an accessory configuration exceeds the 6.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate showing the error and once the configuration has been adjusted to lower than 6.2A, the RESET button can be pressed and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed. The DB-8 is also compatible with Sony Venice and Venice 2 and start / stop capability can be added using the optional adapter cable. INPUTS BATT Gold Mount plate with Anton Bauer communicationDC IN 4pin XLR (11-17V) OUTPUTS 2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-8 (Sony Burano, Gold Mount) Power Distribution Box DB-8 (Sony Burano, Gold Mount) attaches directly to the back of the camera body using the V-Mount interface to provide intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable LANC cable enables remote start/stop capability using 3pin Fischer devices. When using communicative batteries, data is converted to SMBus and sent to the camera enabling percentage data on the monitor. Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-8 will switch to an onboard battery. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the Burano uses approximately 2.8A at 14V so when using a 10A capable battery, the remaining 6.2A is allocated for accessory use. If an accessory configuration exceeds the 6.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate showing the error and once the configuration has been adjusted to lower than 6.2A, the RESET button can be pressed and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed. The DB-8 is also compatible with Sony Venice and Venice 2 and start / stop capability can be added using the optional adapter cable. INPUTS BATT Gold Mount plate with Anton Bauer communicationDC IN 4pin XLR (11-17V) OUTPUTS 2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-8 (Sony Burano, V-Mount) Power Distribution Box DB-8 (Sony Burano, V-Mount) attaches directly to the back of the camera body using the V-Mount interface to provide intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable LANC cable enables remote start/stop capability using 3pin Fischer devices. Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-8 will switch to an onboard battery. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the Burano uses approximately 2.8A at 14V so when using a 10A capable battery, the remaining 6.2A is allocated for accessory use. If an accessory configuration exceeds the 6.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate showing the error and once the configuration has been adjusted to lower than 6.2A, the RESET button can be pressed and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.The DB-8 is also compatible with Sony Venice and Venice 2 and start / stop capability can be added using the optional adapter cable.INPUTSBATT V-Mount plate with SMBus communicationDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-8 (Sony Burano, V-Mount) Power Distribution Box DB-8 (Sony Burano, V-Mount) attaches directly to the back of the camera body using the V-Mount interface to provide intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable LANC cable enables remote start/stop capability using 3pin Fischer devices. Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-8 will switch to an onboard battery. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the Burano uses approximately 2.8A at 14V so when using a 10A capable battery, the remaining 6.2A is allocated for accessory use. If an accessory configuration exceeds the 6.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate showing the error and once the configuration has been adjusted to lower than 6.2A, the RESET button can be pressed and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.The DB-8 is also compatible with Sony Venice and Venice 2 and start / stop capability can be added using the optional adapter cable.INPUTSBATT V-Mount plate with SMBus communicationDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-9 (Blackmagic PYXIS, V-Mount)Power Distribution Box DB-9 (Blackmagic PYXIS, V-Mount) attaches directly to the camera body using the rear two 1/4-20 threaded holes and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable REMOTE USB-C cable enables remote start/stop capability using 3pin Fischer devices.Also available in a hinged 15mm LW Rod Mount version for attaching further away from the camera.Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery.The mount design allows a Sony BP-U35 battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-9 up and release the battery.The DB-9 can also be separated from its camera mount, revealing a 15mm rod clamp with an internal friction sleeve.With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the C80 uses approximately 1.8A at 14V so when using a 10A capable battery, the remaining 8.2A is allocated for accessory use. If an accessory configuration exceeds the 8.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 8.2A, the RESET button can be pressed, and power will be re-enabled to accessory outputs.In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.User changeable Gold Mount Plates are available as wellINPUTS BATT V-Mount plateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box DB-9 (Blackmagic PYXIS, V-Mount)Power Distribution Box DB-9 (Blackmagic PYXIS, V-Mount) attaches directly to the camera body using the rear two 1/4-20 threaded holes and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable REMOTE USB-C cable enables remote start/stop capability using 3pin Fischer devices.Also available in a hinged 15mm LW Rod Mount version for attaching further away from the camera.Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery.The mount design allows a Sony BP-U35 battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-9 up and release the battery.The DB-9 can also be separated from its camera mount, revealing a 15mm rod clamp with an internal friction sleeve.With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the C80 uses approximately 1.8A at 14V so when using a 10A capable battery, the remaining 8.2A is allocated for accessory use. If an accessory configuration exceeds the 8.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 8.2A, the RESET button can be pressed, and power will be re-enabled to accessory outputs.In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.User changeable Gold Mount Plates are available as wellINPUTS BATT V-Mount plateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

MID49 Power Distribution Box Hinge Adapter (15mm LW)SKU: M49-DBHA-15LWPower Distribution Box Hinge Adapter (15mm LW) attaches to the DB-4, DB-9, and DB-11 Power Distribution Boxes to allow them to be mounted on 15mm LW Rods. The friction rod clamp allows for tilted positioning and adjustment without loosening a thumbscrew

PATONA Platinum B-Mount battery with 290Wh 10.1Ah incl. USB-C PD60W input and output 2x D-Tap 16V Discover the latest innovation in our PATONA Platinum series: the B-Mount batteries. Equipped with advanced cell technology, these batteries offer outstanding performance and reliability for the highest demands. Their powerful protection circuits continuously monitor cell balance, temperature, overcharging, and over-discharging to ensure maximum safety and operational efficiency.The integrated OLED display provides a clear overview of the remaining capacity, keeping you well informed at all times. With the versatile D-Tap output, you can easily connect lights and other external devices. The USB-A and USB-C ports allow you to conveniently charge smartphones, tablets, and other devices.A highlight of the Platinum B-Mount battery is its integrated power bank function. Charge devices up to 60W and enjoy the freedom of mobile power supply.By pressing the Power-Check button twice, you activate the LED light on the back of the battery, making the B-Mount plate easily visible even in dark production environments. Pressing the Power-Check button twice again turns the light off, giving you full control over the lighting at all times. This thoughtful feature optimizes handling and ensures you can work efficiently even under challenging conditions.Technical DataVoltage: 28.8 VoltsCapacity: 10.1Ah / 290WhConstant Load: 250W, 10AMaximum Charging Current: 165W, 5AFast Charging: 100W, 3ACell Type: Li-IonNumber of Cells: 24x 18650GAIntegrated LED LightD-Tap 2x Output Voltage: max. 50W, 16V/3.1AUSB-C Port Input: PD 60W, 15V/20V (Max.) 3A -> 5.5h charging time to 100%USB-C Port Output: 60W, 5V/9V/12V/15V/20V (Max.) 3A, BC1.2, PD2.0/3.0, QC2.0/3.0, FCP, SCPUSB-A Port: 10W, 5V/2ACharging Temperature Range: 0 - 40°C Discharge Temperature: -20 - 50°CWeight: 1484gSize: 143 x 101 x 70 mmThe battery is compatible with the following modelsBlackmagic URSA CineARRI ALEXA 35

PATONA 4 position V-Mount charger With this parallel charger you can charge up to 4 V-Mount batteries (with 3 Ampere each) at the same time. Furthermore, it can be used in power supply mode with devices to 60 Watts. The charger has a strong outer material made of black painted metal as well as a practical carrying handle. On top of that, into the front is a XLR 4-pin DC Power output integrated. Through this one, the charger can also be used as power supply for LED lights, camcorders or monitors. Other devices can also be operated with it, provided that these are working with a voltage of 15 volts and a maximum power of 4 amps. This power supply function is activated with a three-way toggle switch. In power supply mode, the adoption of the charging function is unfortunately not possible. In contrast of a sequential charger, the parallel charger has great advantages in sophisticated film productions. You can have lunch for an hour, while you're charging all four PATONA V95 V-Mount batteries at the same time comfortably. All four charged batteries reach a capacity about 50% during this time. With a sequential charger, only one of the four batteries would be charged to 50%. The three others would have not received any charge. Of course, this do not happen without a power loss. This is conducted as warm air through a fan from the charger. Technical Data Input: AC 100V-240V 50/60HzOutput: DC 15V / 4A (4 Pin XLR-Anschluss)Output: 16,8V / 3AWeight: 2,7kggold-plated contactscharge indicator In the box 4-fold V-Mount charger 1x mains cable EU / UK 1x 4 Pin XLR cable