Power Distribution

BLUESHAPE MVQUICK V-Mount Hot Swap Adapter

BLUESHAPE MVQUICK V-Mount Hot Swap Adapter MVQUICK is a hot swap system to be installed as a battery interface between the camera (or any other V-lock compatible device) and the battery pack. The main purpose is to allow camera battery replacement without any power interruption through an automatic detection of the battery removal. Additionally, BLUESHAPE MVQUICK provides an alternative power source of about 21Wh to be used as UPS in case of a sudden power failure or extended power requirements. MVQUICK Features About up to 10~15 minutes runtime when used standalone as an UPS backup batteryInstallable on any V-Lock enabled deviceSelf charging through the installed battery, can be charged also on any V-Lock chargersAllow data communication from battery to cameraNEW: enhanced contact protection for safer air transport Technical data Nominal Voltage 14.8VVoltage range 10.8V ~ 16.8VNominal Capacity 1.5Ah, 21WhMax. discharge current 10ASize 142 mm 83 mm x 50mmWeight 0.49Kg1. LED indicators showing state of charge of internal battery2. Push button for capacity check3. Installation interface for external V-Lock battery4. Output connector (power outlet, to camera)5. Data communication selector to enable or disable battery communication to camera6. D-Tap auxiliary connector7. V-Lock interface for MVQUICK installation

€360.00*

gross: €428.40

Free shipping

Core SWX JP-A-FS7 GOLD Mount Jetpack for Sony PXW-FS7

Core SWX JP-A-FS7 GOLD Mount Jetpack for Sony PXW-FS7 The jetpack offers all the power outputs you'll ever need in a super compact design. The JetPack Sony FS7 includes Power connection to your Sony FS7TTwo powertap outputs (power monitors, lights, etc.)One USB output (i.e. Redmote, Tascam DR-05, other USB device)One 5v Lemo output (i.e. Zoom, AJA)Two 12v regulated Hirose 4-pin outputs (i.e. HDV Cameras, DSLRs)One 4-pin XLR power inputMounting bracket for mounting the Jetpack directly to the back of the Sony FS7 as an alternative to the XDCA-FS7 The all aluminum design reduces weight while still being able to handle wear and tear. The JetPack includes three 1/4-20 mounting points, as well as an optional "cheese" backplate, which offers additional 1/4-20 and 3/8-16 tapped holes. Switronix JP-A-FS7 Technical data Size 20.32 cm x 8.89 cm x 4.77 cmWeight 0.77 kgGOLD-mount Battery/4-pin XLR Input DC 11-17vFS7 Power Input Pin DC 11-17v, UnregulatedP-Tap(2) OutputsDC 11-17v, UnregulatedLEMO 2-pin(0B) 5v, 2.5aHRS 4-pin12v, 2.5a. Includes two 12v outputsMounting Points 1/4-20 threads on bottom, and two on backMounting Points M3 screw pattern on back for optional Cheese PlateUSB Output5V, 1a The JetPack will charge an iPad but slower then the Apple brand charger. You will see "Not Charging" on the iPad screen, but that just means 2.1A of current is not being supplied to the device

€464.07*

gross: €552.24

Details

Core SWX JP-DV-S 24" 3-Pin Lemo JetPack Cable to Sony HDV L

Core SWX JP-DV-S Lemo JetPack Cable LEMO CABLE FOR SONY L SERIES JETPACK 7.2V3-PIN Compatible with SONY L Series style camcorders

€49.00*

gross: €58.31

Core SWX JP-LEADS-12 Lemo JetPack Cable to Flying Leads

Core SWX Lemo JetPack Cable do Flying Leads 24" (60.96 cm) Lemo JetPack Cable to Flying Leads, 12v JETPACK 12V, 4-PIN LEMO CABLE WITH FLYING LEADS allows enduser to put their own connector on the opposite end for designated voltage

€40.00*

gross: €47.60

Core SWX JP-MAGIC-12 12V 4-Pin Lemo Cable for Blackmagic

Core SWX JP-MAGIC-12 12V 4-Pin Lemo Cable 12V 4-Pin Lemo Cable for Blackmagic Mini Converters

€40.00*

gross: €47.60

Free shipping

Core SWX JP-V-FS7 V-Mount Jetpack for Sony PXW-FS7

Core SWX JP-V-FS7 V-Mount Jetpack for Sony PXW-FS7 V-Mount Jetpack for Sony PXW-FS7 The jetpack offers all the power outputs you'll ever need in a super compact design. The JetPack Sony FS7 includes Power connection to your Sony FS7Two powertap outputs (power monitors, lights, etc.)One USB output (i.e. Redmote, Tascam DR-05, other USB device)One 5v Lemo output (i.e. Zoom, AJA)Two 12v regulated Hirose 4-pin outputs (i.e. HDV Cameras, DSLRs)One 4-pin XLR power inputMounting bracket for mounting the Jetpack directly to the back of the Sony FS7 as an alternative to the XDCA-FS7 The all aluminum design reduces weight while still being able to handle wear and tear. The Switronix JetPack includes three 1/4-20 mounting points, as well as an optional "cheese" backplate, which offers additional 1/4-20 and 3/8-16 tapped holes. JP-V-FS7 Technical data Size 20.32 cm x 8.89 cm x 4.77 cmWeight 0.77 kgV-mount Battery/4-pin XLR Input DC 11-17vFS7 Power Input Pin DC 11-17v, UnregulatedP-Tap(2) Outputs DC 11-17v, UnregulatedLEMO 2-pin(0B) 5v, 2.5aHRS 4-pin 12v, 2.5a. Includes two 12v outputsMounting Points1/4-20 threads on bottom, and two on backMounting PointsM3 screw pattern on back for optional Cheese PlateUSB Output5V, 1a. The JetPack will charge an iPad but slower then the Apple brand charger. You will see "Not Charging" on the iPad screen, but that just means 2.1A of current is not being supplied to the device

€464.07*

gross: €552.24

Details

Deity SPD-1 Power Distribution Box

Deity SPD-1 The Deity SPD-1 supports both smart and non-smart batteries with triple DC inputs and hot-swappable functionality. The device also displays battery telemetry data to keep track of your power usage. Monitoring power on set is crucial to keeping production running smoothly. With the SPD-1, you can easily keep track of your power usage, ensuring you never run out of power at the wrong time. This is especially important when stopping production or moving between locations. The SPD-1’s 1.1” color screen provides you with all the information you need, like total power consumption, battery temperatures, voltage, battery life, and battery cycle count. Locking toggle switches make it easy to turn your devices on and off, and this helps prevent losing power randomly. The SPD-1 Power Distribution Box also features dual 1/4” threaded mounts, allowing you to mount the device in any position securely. The reversible mounting clip makes it easy to change the device’s orientation as needed, and the operating range of 12V-18V ensures that it will work with a wide range of devices. In addition, the Power Distribution Box features an easy-access front-facing 5V2A Type A USB port, making it simple to charge your devices and keep them powered up. And with six unregulated 4-Pin Push Power outputs (that are Hirose compatible), you can power multiple devices simultaneously. The six outputs are divided across two power circuit groups so you can toggle on and off auxiliary devices without needing to power down your primary devices. SPD-1 compatibility Sound Devices MX-HIROSE DC Input SledSound Devices 633, 664, 688Sound Devices A10-RX A-TA3 Adapter, A10-RX A-XLRZaxcom Nova, Nova 2Zaxcom Deva 24Zoom F8, F8n, F8n PoZoom F4Sound Devices A10-RX A-TA3 Adapter, A10-RX A-XLRLectrosonics SREXT SR Mounting Kit, DSR4EXT, DCR822Wisycom MCR54 End PlateMiPro MR-90SCSony UWP-D In the box 1x Deity SPD-1 Smart Power Distro1x SPD-T4BATT (TA4f to NH2054 Battery Cup)1x Warranty Card1x Deity Stickers1x QR Card for Digital Manual

€269.00*

gross: €320.11

MID49 Breakout Box and Side Plate Bundle for Blackmagic PYXIS

MID49 Breakout Box and Side Plate Bundle for Blackmagic PYXISSKU: M49-BOB-SPB-BPBreakout Box and Side Plate Bundle for Blackmagic PYXIS includes:Side Plate (Blackmagic PYXIS)A mounting plate that attaches to the side of the camera and provides 1/4-20, 3/8-16 with ARRI locating pins, an ARRI standard rosette, and M4x20mm threaded holes. A marked set of 3/8-16 and 1/4-20 holes are on the sensor axis and the plate is the correct thickness to mount the camera vertically on Baseline 15mm LW (Blackmagic PYXIS) and use 15mm rods at the correct lens heightAudio Breakout AB-9 (Blackmagic PYXIS)A passive adapter that converts the camera's front mini XLR and rear 3.5mm TRS plug into two standard, full-size XLRsInput 1 - balanced audio with phantom power via camera menuInput 2 - unbalanced audio, no phantom power available24 cm cable length with custom low profile mini XLR connector and Neutrik 3.5mm TRS.

€268.00*

gross: €318.92

Free shipping

MID49 Breakout Boxes and Side Plate Bundle For Canon C400

MID49 Breakout Boxes and Side Plate Bundle For Canon C400 SKU: M49-BOB-SPB-C4 Breakout Boxes and Side Plate Bundle for Canon C400 includesBreakout Side Plate for Canon C400, which attaches to the ARRI rosette on the side of the camera and provides a 15mm rod clamp for attaching lens motors, a female ARRI rosette for attaching Canon's handgrip, and a breakout box mounting area with 1/4-20's and recessed cable loops for attaching the included breakout boxes AB-10 and EB-10.Audio Breakout AB-10 (Canon C400) is a passive adapter that converts the camera's two mini XLRs using a custom, low-profile connection to two standard, full-size XLRs.DIN Timecode Genlock Breakout EB-10 (Canon C400) converts the DIN 1.0/2.3 connectors using a custom, low-profile connection to standard BNCs for Timecode and Genlock.Also included is a 1/4-20 knurled knob for attaching Canon's microphone shock mount to the top of the breakout panel.

€540.00*

gross: €642.60

MID49 Breakout Boxes and Side Plate Bundle for RED KOMODO-X

MID49 Breakout Boxes and Side Plate BundleSKU: M49-BOB-SPB-X Breakout Boxes and Side Plate Bundle for RED KOMODO-X includesBreakout Side Plate for RED KOMODO and KOMODO-XAB-1 (RED Komodo-X, V-Raptor, ARRI Alexa Mini)EB-1 (RED Komodo, Komodo-X, V-Raptor)

€539.00*

gross: €641.41

MID49 Breakout Boxes and Side Plate Bundle for RED V-Raptor

MID49 Breakout Boxes and Side Plate Bundle for RED V-Raptor SKU: M49-BOB-SPB-VR1 Breakout Boxes and Side Plate Bundle for RED V-Raptor includes: Breakout Side Plate for RED V-Raptor - attaches to the side of the RED V-Raptor and provides 1/4-20, 3/8-16 with ARRI locating pins, an ARRI standard rosette, and M4x20mm threaded holes. Two offset 1/4-20 holes matching RED's spacing allow certain 3rd party products to be attached like GDU Atlas Side Handle (Raptor, Right) AB-1 (RED V-Raptor) - A passive adapter that converts the camera's 5-pin 00 LEMO to two standard, full-size XLRs and attaches by a captive 1/4-20 screw and rubber pad. EB-1 (RED Komodo, Komodo-X, V-Raptor) - An EXT port converter that provides industry-standard connectors: Genlock: 75-ohm BNCTimecode: 5-pin 0BCTRL: 4-pin 00Trigger: 3-pin FischerEXT Pass-Through: 9-pin 0B

€580.00*

gross: €690.20

Free shipping

MID49 DIN Timecode Genlock Breakout EB-10 (Canon C400)

MID49 DIN Timecode Genlock Breakout EB-10 For Canon C400 SKU: M49-BOB-EB10 DIN Timecode Genlock Breakout EB-10 (Canon C400) converts the DIN 1.0/2.3 connectors to standard BNCs for Timecode and Genlock. Attaches by a captive 1/4-20 screw and rubber pad to the camera body or optional Breakout Side Plate for Canon C400 for clean cable management.Two M4 threaded holes in 20mm ARRI spacing are available to add Breakout Box Mounting Bracket (ARRI 3/8-16, Rear Mount) (sold separately), which allows the EB-10 to attach using a 3/8-16 screw with ARRI locating pins. 23cm cable length with custom low profile dual DIN male interface.

€245.00*

gross: €291.55

MID49 EXT Breakout EB-1 (RED Komodo, Komodo-X, V-Raptor)

MID49 EXT Breakout EB-1 SKU: M49-BOB-EB1 EXT Breakout EB-1 (RED Komodo, Komodo-X, V-Raptor) converts the camera's 9-pin 0B LEMO EXT port to industry standard connectors listed below. Genlock: 75-ohm BNCTimecode: 5-pin 0BCTRL: 4-pin 00Trigger: 3-pin FischerEXT Pass-Through: 9-pin 0B Attaches by a captive 1/4-20 screw and rubber pad to the camera body or side plates like Breakout Side Plate Only (RED Komodo-X)(sold separately). Two M4 threaded holes in 20mm ARRI spacing are available to add Breakout Box Mounting Bracket (ARRI 3/8-16, Rear Mount) (sold separately), which allows the EB-1 to attach using a 3/8-16 screw with ARRI locating pins. 8 inch (20cm) cable length with right angle LEMO-compatible connector. Weight: 70gDimensions (WxLxH): 54 x 271 x 19mm

€340.00*

gross: €404.60

MID49 Power Distribution Box DB-10 (Canon C400) M49-DB10-G

Battary Mount: GOLD-Mount

MID49 Power Distribution Box DB-10 (Canon C400)Power Distribution Box DB-10 (Canon C400) attaches to the back of the camera using the included ARCA Backpack and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors.Removable REMOTE LANC cable enables remote start/stop capability using 3pin Fischer devices. Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-8 will switch to an onboard battery.The ARCA Backpack design allows Canon's BP-A30N battery to be installed in the camera to function as an emergency backup. To swap the internal battery, unlock the ARCA Backpack thumbscrew, slide up, and release the battery.With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the C400 uses approximately 1.6A at 14V so when using a 10A capable battery, the remaining 8.4A is allocated for accessory use. If an accessory configuration exceeds the 8.4A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate showing the error and once the configuration has been adjusted to lower than 8.4A, the RESET button can be pressed and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.The DB-10 is also compatible with Canon C300mkIII and Canon C500mkII start/stop capability requires a longer REMOTE LANC cable.INPUTSBATT V-Mount plate / Gold Mount PlateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

Variants from €750.00*

€883.95*

gross: €1,051.90

MID49 Power Distribution Box DB-10 (Canon C400) M49-DB10-V

Battary Mount: V-Mount

€750.00*

gross: €892.50

Free shipping

MID49 Power Distribution Box DB-11 (Sony FX6, V-Mount) Camera Mounted

DB-11: M49-DB11-V-CM

MID49 Power Distribution Box DB-11 (Sony FX6, V-Mount)Power Distribution Box DB-11 (Sony FX6, V-Mount) attaches directly to the rear two 1/4-20s of the camera body and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors.Removable REMOTE LANC cable enables remote start/stop capability using 3pin Fischer devices. Also available in a hinged 15mm LW Rod Mount version for attaching further away from the camera. Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery.The mount design allows for a Sony BP-U battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-11 up and release the battery. Note that the DB-11 provides 19.5V to the camera so that the camera will default to the DC input.The DB-11 can also be separated from its camera mount, revealing a 15mm rod clamp with an internal friction sleeve. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the FX6 uses approximately 1.0A at 14V so when using a 10A capable battery, the remaining 9.0A is allocated for accessory use. If an accessory configuration exceeds the 9.0A limit, accessory power is cut off, leaving the camera powered.The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 9.0A, the RESET button can be pressed, and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed. The DB-11 is also compatible with Sony FX9, but that camera's mounting points are in a different location so the Rod Mounted version is suggested.User changeable Gold Mount Plates available as well.INPUTSBATT V-Mount plateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

€893.95*

gross: €1,063.80

Free shipping

MID49 Power Distribution Box DB-11 (Sony FX6, V-Mount) Rod Mounted

DB-11: M49-DB11-V-RM

€893.95*

gross: €1,063.80

Free shipping

MID49 Power Distribution Box DB-4 (Canon C80, V-Mount) Camera Mounted

DB-4 (Canon C80, V-Mount): M49-DB4-V-CM

MID49 Power Distribution Box DB-4 (Canon C80, V-Mount)Power Distribution Box DB-4 (Canon C80, V-Mount) attaches directly to the shoe mount of the C80 using locking pins and pressure and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable REMOTE LANC cable enables remote start/stop capability using 3pin Fischer devices.Also available in a hinged 15mm LW Rod Mount version for attaching further away from the camera.Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery. The shoe mount design allows Canon's BP-A30N battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-4 up and release the battery. Note that the DB-4 provides 19.5V to the camera so that the camera will default to the DC input.The DB-4 can also be separated from its shoe mount, revealing a 15mm rod clamp with an internal friction sleeve. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the C80 uses approximately 1.0A at 14V so when using a 10A capable battery, the remaining 9.0A is allocated for accessory use. If an accessory configuration exceeds the 9.0A limit, accessory power is cut off, leaving the camera powered.The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 9.0A, the RESET button can be pressed, and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.The DB-4 is also compatible with Canon C70 but that camera's shoe is in a different location so the Rod Mounted version is suggested. User changeable Gold Mount Plates are available as well.INPUTSBATT V-Mount plateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

€893.95*

gross: €1,063.80

Free shipping

MID49 Power Distribution Box DB-4 (Canon C80, V-Mount) Rod Mounted

DB-4 (Canon C80, V-Mount): M49-DB4-V-RM

€893.95*

gross: €1,063.80

MID49 Power Distribution Box DB-8 (Sony Burano, Gold Mount) M49-DB8-G

DB-8: BURANO only

MID49 Power Distribution Box DB-8 (Sony Burano, Gold Mount) Power Distribution Box DB-8 (Sony Burano, Gold Mount) attaches directly to the back of the camera body using the V-Mount interface to provide intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable LANC cable enables remote start/stop capability using 3pin Fischer devices. When using communicative batteries, data is converted to SMBus and sent to the camera enabling percentage data on the monitor. Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-8 will switch to an onboard battery. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the Burano uses approximately 2.8A at 14V so when using a 10A capable battery, the remaining 6.2A is allocated for accessory use. If an accessory configuration exceeds the 6.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate showing the error and once the configuration has been adjusted to lower than 6.2A, the RESET button can be pressed and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed. The DB-8 is also compatible with Sony Venice and Venice 2 and start / stop capability can be added using the optional adapter cable. INPUTS BATT Gold Mount plate with Anton Bauer communicationDC IN 4pin XLR (11-17V) OUTPUTS 2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

€850.00*

gross: €1,011.50

MID49 Power Distribution Box DB-8 (Sony Burano, Gold Mount) M49-DB8-G-CBL-V

DB-8: Sony Venice/Venice 2 Adaptor Cable

Variants from €850.00*

€950.00*

gross: €1,130.50

Free shipping

MID49 Power Distribution Box DB-8 (Sony Burano, V-Mount) M49-DB8-V

DB-8: BURANO only

MID49 Power Distribution Box DB-8 (Sony Burano, V-Mount) Power Distribution Box DB-8 (Sony Burano, V-Mount) attaches directly to the back of the camera body using the V-Mount interface to provide intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable LANC cable enables remote start/stop capability using 3pin Fischer devices. Hot swap between onboard battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-8 will switch to an onboard battery. With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the Burano uses approximately 2.8A at 14V so when using a 10A capable battery, the remaining 6.2A is allocated for accessory use. If an accessory configuration exceeds the 6.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate showing the error and once the configuration has been adjusted to lower than 6.2A, the RESET button can be pressed and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.The DB-8 is also compatible with Sony Venice and Venice 2 and start / stop capability can be added using the optional adapter cable.INPUTSBATT V-Mount plate with SMBus communicationDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

€841.95*

gross: €1,001.92

Free shipping

MID49 Power Distribution Box DB-8 (Sony Burano, V-Mount) M49-DB8-V-CBL-V

DB-8: Sony Venice/Venice 2 Adaptor Cable

Variants from €841.95*

€931.95*

gross: €1,109.02

Free shipping

MID49 Power Distribution Box DB-9 (Blackmagic PYXIS, V-Mount) Camera Mounted

DB-9 (Blackmagic PYXIS): M49-DB9-V-CM

MID49 Power Distribution Box DB-9 (Blackmagic PYXIS, V-Mount)Power Distribution Box DB-9 (Blackmagic PYXIS, V-Mount) attaches directly to the camera body using the rear two 1/4-20 threaded holes and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors. Removable REMOTE USB-C cable enables remote start/stop capability using 3pin Fischer devices.Also available in a hinged 15mm LW Rod Mount version for attaching further away from the camera.Hot-swap between on-board battery and 4pin XLR DC INPUT without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 12.5V at which point, the DB-4 will switch to an onboard battery.The mount design allows a Sony BP-U35 battery to be installed in the camera to function as an emergency backup. To swap the internal battery, swing the DB-9 up and release the battery.The DB-9 can also be separated from its camera mount, revealing a 15mm rod clamp with an internal friction sleeve.With the SMART FUSE design, camera power is monitored and the remaining power budget is allocated to accessories. For example, the C80 uses approximately 1.8A at 14V so when using a 10A capable battery, the remaining 8.2A is allocated for accessory use. If an accessory configuration exceeds the 8.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 8.2A, the RESET button can be pressed, and power will be re-enabled to accessory outputs.In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.User changeable Gold Mount Plates are available as wellINPUTS BATT V-Mount plateDC IN 4pin XLR (11-17V)OUTPUTS2x D-Tap (battery voltage)2x 3pin (24V at 2.5A with run/stop)2x 2pin (battery voltage)1x USB-C PD (5V at 3A with thread lock)

€950.00*

gross: €1,130.50

Filter products

The professional source for Filmmakers in Düsseldorf

We provide best equipment and advice in the field of professional video- and audio- technology