MID49 Baseline 15mm LW For Canon C400, C300 MK III, C500 MK II, C200, C200B, C700 / Blackmagic Pocket 6K / Kinefinity MAVO Mark 2 BaseplateSKU: M49-BSL-LW13-AC7 Baseline 15mm LW for Canon C400, C300 MK III, C500 MKII, C200, C200B, C700 / Blackmagic Pocket 6K / Kinefinity MAVO Mark 2 is a baseplate that holds 15mm lightweight rods at the correct distance from the center of the lens on the listed cameras. ARRI dovetail slot on the bottom attaches to the included Baseline ARRI Dovetail or other ARRI standard dovetails using a top-load locking mechanism. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew.Baseline ARRI Dovetail is the included lower ARRI mounting plate which can attach to tripod plates using 1/4-20 or 3/8-16 screws or ARRI standard bridgeplates with centered or offset screw spacing. ARCA dovetail slot on top holds the included ARCA Dovetail and can be top-loaded, or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until ARCA clamp has opened fully. Reverse the process to tighten.Center screw slot on ARCA Dovetail accepts 1/4-20 and 3/8-16 mounting screws, and a vertical rod hole clamps included 1/4-20 lens support posts for adaptors like Metabones, etc.Rod Bracket 15mm LW (sold separately) can be attached to the back of the baseplate for rear 15mm LW rod support.Individual components of this kit are also availableBaseline Core 15mm LW (13mm Platform Height)Baseline ARCA Dovetail (7.5mm Height)Baseline ARRI Dovetail

MID49 Baseline 15mm LW (FUJIFILM GFX ETERNA)SKU: M49-BSL-FUJE-LWBaseline 15mm LW (FUJIFILM GFX ETERNA) is a baseplate that holds 15mm lightweight rods at the correct distance from the center of the lens and attaches to the bottom of the camera by three 3/8-16 screws. The center of the LW 15mm Bracket has a 1/4-20 vertical support post, which can be used to support lens adapters like Metabones, etc.ARRI dovetail slot on the bottom attaches to the included Baseline ARRI Dovetail or other ARRI standard dovetails using a top-load locking mechanism. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew.Baseline ARRI Dovetail is the included lower ARRI mounting plate, which can attach to tripod plates using 1/4-20 or 3/8-16 screws or ARRI standard bridgeplates with centered or offset screw spacing. ==ARRI M6 rosette on the right side allows the attachment of a camera side handle or optional ARRI Rosette to NATO Rail for additional accessory mounting options.This Baseline Baseplate does not have an upper ARCA slot but has ARCA geometry hidden on the bottom, which will accept the Gimbal Bottom ARCA Adapter (DJI S, RS2, RS3, RS4), Gimbal Bottom ARCA Adapter (DJI Ronin 2), and Gimbal Bottom ARCA Adapter (Freefly Mōvi Pro). These adapters enable quick and tool-free transition from tripod to gimbal modes.Individual components of this kit are also availableBaseline Core 15mm LW (FUJIFILM GFX ETERNA)LW 15mm Rod Bracket (FUJIFILM GFX ETERNA)Baseline ARRI DovetailProduct Weight: 438g

MID49 Baseline 15mm LW (RED KOMODO, KOMODO-X / Blackmagic Pocket 4K / FREEFLY Ember S5K Baseplate) SKU: M49-BSL-LW23-AC14 Baseline 15mm LW (RED KOMODO, KOMODO-X / Blackmagic Pocket 4K / FREEFLY Ember S5K Baseplate) is a baseplate that holds 15mm lightweight rods at the correct distance from the center of the lens. ARRI dovetail slot on the bottom attaches to the included Baseline ARRI Dovetail or other ARRI standard dovetails using a top-load locking mechanism. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew. Baseline ARRI Dovetail is the included lower ARRI mounting plate which can attach to tripod plates using 1/4-20 or 3/8-16 screws or ARRI standard bridgeplates with centered or offset screw spacing. ARCA dovetail slot on top holds the included ARCA Dovetail and can be top-loaded, or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until ARCA clamp has opened fully. Reverse the process to tighten. Center screw slot on ARCA Dovetail accepts 1/4-20 and 3/8-16 mounting screws, and a vertical rod hole clamps included 1/4-20 lens support posts for adaptors like Metabones, etc. Rod Bracket (15mm LW) (sold separately) can be attached to the back of the baseplate for rear 15mm LW rod support. Individual components of this kit are also available: Baseline Core 15mm LW (23mm Platform Height)Baseline ARCA Dovetail (14.5mm Height)Baseline ARRI Dovetail Technical data Product Weight: 350gProduct Dimensions (WxLxH): 123 x 140 x 58mm

MID49 Baseline 15mm LW (RED V-Raptor Baseplate) SKU: M49-BSL-LW23-AC7 Baseline 15mm LW (RED V-Raptor Baseplate) is a baseplate that holds 15mm lightweight rods at the correct distance from the center of the lens.ARRI dovetail slot on the bottom attaches to the included Baseline ARRI Dovetail or other ARRI standard dovetails using a top-load locking mechanism. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew. Baseline ARRI Dovetail is the included lower ARRI mounting plate which can attach to tripod plates using 1/4-20 or 3/8-16 screws or ARRI standard bridgeplates with centered or offset screw spacing. ARCA dovetail slot on top holds the included ARCA Dovetail and can be top-loaded, or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until ARCA clamp has opened fully. Reverse the process to tighten. Center screw slot on ARCA Dovetail accepts 1/4-20 and 3/8-16 mounting screws, and a vertical rod hole clamps included 1/4-20 lens support posts for adaptors like Metabones, etc. Rod Bracket (15mm LW) (sold separately) can be attached to the back of the baseplate for rear 15mm LW rod support. Individual components of this kit are also available: Baseline Core 15mm LW (23mm Platform Height)Baseline ARCA Dovetail (7.5mm Height)Baseline ARRI Dovetail Technical data Product Weight: 330gProduct Dimensions (WxLxH): 123 x 140 x 51mm

MID49 Baseline 15mm LW (Sony Burano, FX6, Venice, Venice 2, Rialto, F55, F5 / Blackmagic URSA Mini, Mini Pro, Mini Pro 12K Baseplate)SKU: M49-BSL-LW0-AC12 Baseline 15mm LW (Sony FX6, Venice, Venice 2, Rialto, F55, F5 / Blackmagic URSA Mini, Mini Pro, Mini Pro 12K Baseplate) is a baseplate that holds 15mm lightweight rods at the correct distance from the center of the lens on the listed cameras. ARRI dovetail slot on the bottom attaches to the included Baseline ARRI Dovetail or other ARRI standard dovetails using a top-load locking mechanism. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew. Baseline ARRI Dovetail is the included lower ARRI mounting plate which can attach to tripod plates using 1/4-20 or 3/8-16 screws or ARRI standard bridgeplates with centered or offset screw spacing. ARCA dovetail slot on top holds the included ARCA Dovetail and can be top-loaded, or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until ARCA clamp has opened fully. Reverse the process to tighten. Center screw slot on ARCA Dovetail accepts 1/4-20 and 3/8-16 mounting screws, and a vertical rod hole clamps included 1/4-20 lens support posts for adaptors like Metabones, etc. Individual components of this kit are also available: Baseline Core 15mm LW (0mm Platform Height)Baseline ARCA Dovetail (12mm Height)Baseline ARRI DovetailTechnical dataProduct Weight: 334gProduct Dimensions (WxLxH): 123 x 140 x 33mm

MID49 Baseline 15mm LW (Sony FS5, Panasonic EVA1, VariCam LT, VariCam 35 Baseplate) SKU: M49-BSL-LW13-AC12 Baseline 15mm LW (Sony FS5, Panasonic EVA1, VariCam LT, VariCam 35 Baseplate) is a baseplate that holds 15mm lightweight rods at the correct distance from the center of the lens on the listed cameras. ARRI dovetail slot on the bottom attaches to the included Baseline ARRI Dovetail or other ARRI standard dovetails using a top-load locking mechanism. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew. Baseline ARRI Dovetail is the included lower ARRI mounting plate which can attach to tripod plates using 1/4-20 or 3/8-16 screws or ARRI standard bridgeplates with centered or offset screw spacing. ARCA dovetail slot on top holds the included ARCA Dovetail and can be top-loaded, or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until ARCA clamp has opened fully. Reverse the process to tighten. Center screw slot on ARCA Dovetail accepts 1/4-20 and 3/8-16 mounting screws, and a vertical rod hole clamps included 1/4-20 lens support posts for adaptors like Metabones, etc. Rod Bracket (15mm LW)(sold separately) can be attached to the back of the baseplate for rear 15mm LW rod support. Individual components of this kit are also available: Baseline Core 15mm LW (13mm Platform Height)Baseline ARCA Dovetail (12mm Height)Baseline ARRI Dovetail Technical data Product Weight: 346gProduct Dimensions (WxLxH): 123 x 140 x 45mm

MID49 Baseline 15mm LW (Sony FX9, FS7, FS7mkII / Canon C100mkII, C300mkII, C100, C300, C500 Baseplate) SKU: M49-BSL-LW0-AC7 Baseline 15mm LW (Sony FX9, FS7, FS7mkII / Canon C100mkII, C300mkII, C100, C300, C500 Baseplate) is a baseplate that holds 15mm lightweight rods at the correct distance from the center of the lens on the listed cameras. ARRI dovetail slot on the bottom attaches to the included Baseline ARRI Dovetail or other ARRI standard dovetails using a top-load locking mechanism. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew. Baseline ARRI Dovetail is the included lower ARRI mounting plate which can attach to tripod plates using 1/4-20 or 3/8-16 screws or ARRI standard bridgeplates with centered or offset screw spacing. ARCA dovetail slot on top holds the included ARCA Dovetail and can be top-loaded, or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until ARCA clamp has opened fully. Reverse the process to tighten. Center screw slot on ARCA Dovetail accepts 1/4-20 and 3/8-16 mounting screws, and a vertical rod hole clamps included 1/4-20 lens support posts for adaptors like Metabones, etc. Rod Bracket (15mm LW)(sold separately) can be attached to the back of the baseplate for rear 15mm LW rod support. Individual components of this kit are also available Baseline Core 15mm LW (0mm Platform Height)Baseline ARCA Dovetail (7.5mm Height)Baseline ARRI DovetailTechnical dataProduct Weight: 322gProduct Dimensions (WxLxH): 123 x 140 x 30mm

MID49 Baseline 15mm LW (Upper Cage Canon C50)SKU: M49-BSL-LW-19Baseline 15mm LW (Upper Cage Canon C50) holds two 15mm rods at 15mm lightweight spacing when combined with the Upper Cage Canon C50.ARRI dovetail slot on the bottom attaches using a top-load locking mechanism to included Baseline ARRI Dovetail or other ARRI standard dovetails.Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew.ARCA dovetail slot on top holds Baseline ARCA Dovetails and can be top-loaded, or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until ARCA clamp has opened fully. Reverse the process to tighten.

MID49 Baseline 15mm LW (Upper Cage Nikon ZR)SKU: M49-BSL-LW19-ZRBaseline 15mm LW (Upper Cage Nikon ZR) holds two 15mm rods at 15mm lightweight spacing when combined with the Upper Cage Nikon ZR. Note that this is the same lens height as the version for the Canon C50, however, this assembly has a shorter thumbscrew and safety button to allow the Nikon battery and memory card to be changed without removing the baseplate. ARRI dovetail slot on the bottom attaches using a top-load locking mechanism to the included Baseline ARRI Dovetail or other ARRI standard dovetails. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged.Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew. ARCA dovetail slot on top holds Baseline ARCA Dovetails and can be top-loaded, or installed from the back by sliding in.When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until the ARCA clamp has opened fully. Reverse the process to tighten.Weight: 156g

MID49 Baseline 15mm LW (Upper Cage Sony FX2)SKU: M49-BSL-LW26-0Baseline 15mm LW (Upper Cage Sony FX2) holds two 15mm rods at 15mm lightweight spacing when combined with the Upper Cage Sony FX2. ARRI dovetail slot on the bottom attaches using a top-load locking mechanism to included Baseline ARRI Dovetail or other ARRI standard dovetails. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew.ARCA dovetail slot on top holds Baseline ARCA Dovetails and can be top-loaded, or installed from the back by sliding in. When sliding in from the back, a safety pin will engage with a pop when properly installed. Adjust the position, then lock the ratcheting thumbscrew. Top-loading can be achieved by loosening the thumbscrew, pulling out on the ratcheting knob, and turning the thumbscrew until ARCA clamp has opened fully. Reverse the process to tighten.

MID49 Baseline ARRI Dovetail SKU: M49-BSL-ARR-0 Baseline ARRI Dovetail is the lower ARRI mounting plate included in the Baseline 15mm LW series. Attaches to tripod plates or ARRI standard bridgeplates with centered or offset screw spacing. 1/4-20 and 3/8-16 threaded holes available in standard spacing. Thin dovetail design and stopper screws are designed specifically for the Baseline series and are not for mounting bridgeplates directly. Weight: 66gDimensions (WxLxH): 67 x 140 x 6mm

MID49 Baseline Bridgeplate 15mm StudioSKU: M49-BSL-BRP-15S Baseline Bridgeplate (15mm Studio) is a quick-release, ARRI standard bridge plate that, when combined with Baseline 15mm LW baseplates, provides 15mm studio offset rods at the correct distance from the center of the lens. ARRI dovetail slot on the bottom attaches to ARRI standard dovetails using a top-load locking mechanism. Unlock the lever like a traditional bridge plate, pull the safety release, then further move the lever, which allows the camera to be released vertically from the dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the lever. Baseline Bridgeplates can also be installed and removed from the back of most ARRI standard dovetails. Included (2) 3/8-16 and (2) 1/4-20 screws can be installed using the center screw channel into the offset screw holes on the Baseline ARRI Dovetail.

MID49 Baseline Bridgeplate 19mmSKU: M49-BSL-BRP-19 Baseline Bridgeplate (19mm) is a quick-release, ARRI standard bridge plate that, when combined with Baseline 15mm LW baseplates, provides 19mm rods at the correct distance from the center of the lens. ARRI dovetail slot on the bottom attaches to ARRI standard dovetails using a top-load locking mechanism. Unlock the lever like a traditional bridge plate, pull the safety release, then further move the lever, which allows the camera to be released vertically from the dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the lever. Baseline Bridgeplates can also be installed and removed from the back of most ARRI standard dovetails. Included (2) 3/8-16 and (2) 1/4-20 screws can be installed using the center screw channel or by two offset holes when using some ARRI brand products.

MID49 Baseline Core (FUJIFILM GFX ETERNA)SKU: M49-BSL-LWB-FUJEBaseline Core (FUJIFILM GFX ETERNA) is the baseplate riser that attaches to the bottom of the camera by three 3/8-16 screws. An optional 15mm Bracket can be purchased separately or as a complete baseplate kit. ARRI dovetail slot on the bottom attaches to ARRI standard dovetails using a top-load locking mechanism. Loosen the thumbscrew and push the silver button on the operator's side to release the baseplate from the ARRI dovetail. To reattach, drop down and listen for the pop to know it has engaged. Adjust the position on the ARRI dovetail, then lock the ratcheting thumbscrew.To attach the Core to a tripod or bridgeplate, the Baseline ARRI Dovetail is required, which is an ARRI mounting plate with 1/4-20 and 3/8-16 threaded holes. The dovetail can be purchased separately or as a complete baseplate kit. ARRI M6 rosette on the right side allows the attachment of a camera side handle or optional ARRI Rosette to NATO Rail for additional accessory mounting options. This Baseline Baseplate does not have an upper ARCA slot but has ARCA geometry hidden on the bottom, which will accept the Gimbal Bottom ARCA Adapter (DJI S, RS2, RS3, RS4), Gimbal Bottom ARCA Adapter (DJI Ronin 2), and Gimbal Bottom ARCA Adapter (Freefly Mōvi Pro). These adapters enable quick and tool-free transition from tripod to gimbal modes.

MID49 Baseline Core 15mm LW (0mm Platform Height) SKU: M49-BSL-LWB-0 Baseline Core 15mm LW (0mm Platform Height) holds two 15mm rods at 15mm lightweight spacing when combined with the camera dovetails listed below. "0mm" platform height refers to the distance from the center of the 15mm rods to the bottom of the ARCA dovetail. Combine with the below Baseline ARCA Dovetails and listed cameras for lightweight 15mm rods at the correct lens height. Baseline ARCA Dovetail (7.5mm Height) Sony FX9, FS7, FS7mkIICanon C100, C300, C500, C100mkII, C300mkII Baseline ARCA Dovetail (12mm Height) Sony FX6, Venice, Venice 2, Rialto, F55, F5Blackmagic URSA Mini, Mini Pro, Mini Pro 12K Technical data Product Weight: 156gProduct Dimensions (WxLxH): 123 x 93 x 30mm

MID49 Baseline Core 15mm LW (13mm Platform Height) SKU: M49-BSL-LWB-13 Baseline Core 15mm LW (13mm Platform Height) holds two 15mm rods at 15mm lightweight spacing when combined with the camera dovetails listed below. "13mm" platform height refers to the distance from the center of the 15mm rods to the bottom of the ARCA dovetail. Combine with the below Baseline ARCA Dovetails and listed cameras for lightweight 15mm rods at the correct lens height. Baseline ARCA Dovetail (7.5mm Height) Canon C300mkIII, C500mkII, C200, C200B, C700, Blackmagic Pocket 6K, Kinefinity MAVO mark2 Baseline ARCA Dovetail (12mm Height) Sony FS5, Panasonic EVA1, VariCam LT, VariCam 35 Technical data Product Weight: 166gProduct Dimensions (WxLxH): 123 x 93 x 37mm

MID49 Baseline Core 15mm LW (23mm Platform Height) SKU: M49-BSL-LWB-23 Baseline Core 15mm LW (23mm Platform Height) holds two 15mm rods at 15mm lightweight spacing when combined with the camera dovetails listed below. "23mm" platform height refers to the distance from the center of the 15mm rods to the bottom of the ARCA dovetail. Combine with the below Baseline ARCA Dovetails and listed cameras for lightweight 15mm rods at the correct lens height. Baseline ARCA Dovetail (7.5mm Height) RED V-Raptor Baseline ARCA Dovetail (14.5mm Height) RED Komodo, Komodo-X / Blackmagic Pocket 4K Technical data Product Weight: 166gProduct Dimensions (WxLxH): 123 x 83 x 47mm

MID49 Breakout Box Rear Mounting Bracket SKU: M49-BOB-RMB-38 Breakout Box Rear Mounting Bracket (ARRI 3/8-16) attaches by two M4 screws to the side of the EXT Breakout EB-1 (RED Komodo, Komodo-X, V-Raptor) and allows mounting via 3/8-16 screw with ARRI locating pins.Not compatible with Audio Breakout AB-1 (RED Komodo-X, V-Raptor, ARRI Alexa Mini). Weight: 10gDimensions (WxLxH): 20 x 27 x 12mm

MID49 Breakout Box Side Mounting Bracket SKU: M49-BOB-SMB-38 Breakout Box Side Mounting Bracket (ARRI 3/8-16) attaches by two M4 screws to the side of the Audio Breakout AB-1 (RED Komodo-X, V-Raptor, ARRI Alexa Mini) and allows mounting via 3/8-16 screw with ARRI locating pins.Not compatible with EXT Breakout EB-1 (RED Komodo, Komodo-X, V-Raptor). Weight: 15gDimensions (WxLxH): 27 x 24 x 28mm

MID49 Breakout Boxes and Side Plate BundleSKU: M49-BOB-SPB-X Breakout Boxes and Side Plate Bundle for RED KOMODO-X includesBreakout Side Plate for RED KOMODO and KOMODO-XAB-1 (RED Komodo-X, V-Raptor, ARRI Alexa Mini)EB-1 (RED Komodo, Komodo-X, V-Raptor)

MID49 Breakout Boxes and Side Plate Bundle for RED V-Raptor SKU: M49-BOB-SPB-VR1 Breakout Boxes and Side Plate Bundle for RED V-Raptor includes: Breakout Side Plate for RED V-Raptor - attaches to the side of the RED V-Raptor and provides 1/4-20, 3/8-16 with ARRI locating pins, an ARRI standard rosette, and M4x20mm threaded holes. Two offset 1/4-20 holes matching RED's spacing allow certain 3rd party products to be attached like GDU Atlas Side Handle (Raptor, Right) AB-1 (RED V-Raptor) - A passive adapter that converts the camera's 5-pin 00 LEMO to two standard, full-size XLRs and attaches by a captive 1/4-20 screw and rubber pad. EB-1 (RED Komodo, Komodo-X, V-Raptor) - An EXT port converter that provides industry-standard connectors: Genlock: 75-ohm BNCTimecode: 5-pin 0BCTRL: 4-pin 00Trigger: 3-pin FischerEXT Pass-Through: 9-pin 0B

MID49 Breakout Side Bar Only For Canon C400 SKU: M49-BOB-SBO-C4 Breakout Side Bar Only for Canon C400 clamps to a 15mm rod and provides a breakout box mounting area with 1/4-20's and recessed cable loops for attaching the Audio Breakout AB-10 (Canon C400) and DIN Timecode Genlock Breakout EB-10 (Canon C400), which are available separately. Also included is a 1/4-20 knurled knob for attaching Canon's microphone shock mount to the top of the breakout panel.

MID49 Breakout Side Plate For Canon C400 SKU: M49-BOB-SPL-C4 Breakout Side Plate for Canon C400 attaches to the ARRI rosette on the side of the camera and provides a 15mm rod clamp for attaching lens motors, a female ARRI rosette for attaching Canon's handgrip, and a breakout box mounting area with 1/4-20's and recessed cable loops for attaching the Audio Breakout AB-10 (Canon C400) and DIN Timecode Genlock Breakout EB-10 (Canon C400), which are available separately. Also included is a 1/4-20 knurled knob for attaching Canon's microphone shock mount to the top of the breakout panel. The Breakout Side Plate for Canon C400 is available as a discounted kit with the AB-10 and EB-10: Breakout Boxes and Side Plate Bundle for Canon C400

MID49 Breakout Side Plate SKU: M49-BOB-SPL-KX Breakout Side Plate for RED KOMODO and RED KOMODO-X attaches to the side of the RED Komodo and Komodo-X and provides 1/4-20, 3/8-16 with ARRI locating pins, an ARRI standard rosette, and M4x20mm threaded holes. Two offset M4 holes matching RED's spacing allow certain 3rd party products to be attached like GDU Atlas Side Handle (Komodo, Right)When used on RED Komodo-X, rear 1/4-20's provide ideal mounting locations for Audio Breakout AB-1 (RED Komodo-X) and EXT Breakout EB-1 (RED Komodo, Komodo-X).When used on the original RED Komodo, combine with Audio Breakout AB-3 (RED Komodo) and EXT Breakout EB-1 (RED Komodo, Komodo-X).The Side Plate is compatible with RED's PL Mount support, as seen in this installation guide.Recessed cable loops in the side plate allow for clean cable management.