MID49 Right Side Vertical Camera Bracket (Sony Burano / Blackmagic PYXIS)SKU: M49-CAG-VCB-BUPYRight Side Vertical Camera Bracket (Sony Burano / Blackmagic PYXIS) attaches to the Top Plate (Burano) or Top Plate (PYXIS) to allow for vertical video shooting or right-side accessory mounting. 1/4-20 and 3/8-16 threaded holes with ARRI locating pins are spaced at 1-inch intervals, and M4x20mm threaded holes (ARRI MAP) are available in several places. 4x hook and loop straps are included for holding wireless transmitters, receivers, timecode devices, etc.Weight: 148gDimensions: 88.5 x 104 x 11.5mm

MID49 Rod Bracket (15mm LW) SKU: M49-ROD-BRK-15LW Rod Bracket (15mm LW) holds two 15mm rods at 60mm lightweight spacing and attaches by two 1/4-20 screws 18mm apart to the back of Baseline 15mm LW baseplates to add rear rod support. M4 screws 20mm apart can be used instead to attach to products like ARCA Top Handle and ARCA Top Plate (114mm) or other devices with standard ARRI standard M4 spacing. M4x20mm threaded holes are available on top for adding additional accessories.

MID49 Side Plate (Blackmagic PYXIS)SKU: M49-CAG-BMP-SDPSide Plate (Blackmagic PYXIS) attaches to the side of the camera and provides 1/4-20, 3/8-16 with ARRI locating pins, an ARRI standard rosette, and M4x20mm threaded holes. A marked set of 3/8-16 and 1/4-20 holes are on the sensor axis and the plate is the correct thickness to mount the camera vertically on Baseline 15mm LW (Blackmagic PYXIS) and use 15mm rods at the correct lens height. The striped 1/4-20 provides an ideal mounting location for Audio Breakout AB-9 (Blackmagic PYXIS) and recessed cable loops on the back of the side plate allow for clean cable management.Dimensions (WxLxH):88.5 x 104 x 11.5mm

MID49 Single 15mm Rod Clamp (M4 x 20mm) SKU: M49-SRC-15 Single 15mm Rod Clamp (M4 x 20mm) attaches by two M4 screws spaced 20mm apart, center to center, and is great for attaching lens motors in a compact configuration. M4x20mm holes are found on MID49 cheeseplates, handles, audio breakouts, EXT breakouts, and rod clamps, as well as ARRI and many third-party accessories. Weight: 34gDimensions: 28 x 42 x 31mm

MID49 Single 19mm Rod Clamp (M4 x 20mm) SKU: M49-SRC-19 Single 19mm Rod Clamp (M4 x 20mm) attaches by two M4 screws spaced 20mm apart, center to center, and is great for attaching lens motors in a compact configuration. M4x20mm holes are found on MID49 cheeseplates, handles, audio breakouts, EXT breakouts, and rod clamps, as well as ARRI and many third-party accessories. Weight: 34gDimensions: 28 x 42 x 31mm

MID49 Sony Burano EVF Pivot Adaptor SKU: M49-MON-SON-EPA Sony Burano EVF Pivot Adapter allows the Burano LCD panel to switch from monitor configuration to viewfinder configuration without tools. Just grab and twist. Weight: 40gDimensions (WxLxH): 29 x 46 x 21 mm

MID49 Top 15mm Rod Bracket (Sony Burano, Canon C400, Blackmagic PYXIS / URSA Cine LF)SKU: M49-TOP-ROD-15LWTop 15mm Rod Bracket (Sony Burano, Canon C400, Blackmagic PYXIS / URSA Cine LF) attaches to the front of the Top Plates for the listed cameras and holds two 15mm LW rods for adding focus motors, viewfinder mounts, and other accessories over the lens area. Rods pass over the Top Plate and around the ARCA Top Handle and Rainbow Handle while still allowing access for carrying. Great for leaving rod accessories installed when switching to gimbal mode using adapters like Gimbal Top ARCA Adapter (DJI Ronin 2) or (Freefly Mōvi Pro) or the ARCA Top Plate.Compatible Top PlatesTop Plate (Canon C400)Top Plate (Sony Burano)Top Plate (Blackmagic PYXIS)Top Plate (Blackmagic URSA Cine LF)

MID49 Top Plate (Blackmagic PYXIS) SKU: M49-CAG-BMP-TOP Top Plate (Blackmagic PYXIS) attaches to the top of the camera and provides 1/4-20 and 3/8-16 threaded holes with ARRI accessory pins, M4x20mm ARRI standard threaded holes, and ventilation holes for the PYXIS fan. Center ARCA dovetail clamp allows for attachment of the the Rainbow Handle Kit, ARCA Top Handle, ARCA Top Plate, and Gimbal Adapter Plates (Freefly Mōvi Pro and DJI Ronin 2) for quick change between handheld and studio modes. Side 3/8-16 ARRI accessory mounts can accept Cage NATO Side Arm (ARRI 3/8-16) for cage building.Weight: 252gDimensions (WxLxH): 107 x 132 x 24mm

MID49 Top Plate (Blackmagic URSA Cine LF)SKU: M49-CAG-BMUC-TOPTop Plate (Blackmagic URSA Cine LF) attaches to the top of the camera and provides 1/4-20 and 3/8-16 threaded holes with ARRI accessory pins, M4x20mm ARRI standard threaded holes, and provides ventilation for the URSA fan system. Center ARCA dovetail clamp allows for attachment of the Rainbow Handle Kit, ARCA Top Handle, ARCA Top Plate, and Gimbal Adapter Plates (Freefly Mōvi Pro and DJI Ronin 2) for quick change between handheld and studio modes. Side 3/8-16 ARRI accessory mounts can accept Cage NATO Side Arm (ARRI 3/8-16, 135mm) for cage building.Dimensions (WxLxH): 144 x 191 x 23.8mm

MID49 Top Plate (FUJIFILM GFX ETERNA)SKU: M49-CAG-FUJE-TOPTop Plate (FUJIFILM GFX ETERNA) attaches to the top of the camera and provides 1/4-20 and 3/8-16 threaded holes with ARRI accessory pins, and M4x20mm ARRI standard threaded holes.Segmented design allows the original ETERNA handle to be installed in the camera's dovetail slot over the Top Plate. When the top handle is removed, the smaller section of Top Plate can be added.Center ARCA dovetail clamp allows for attachment of the Rainbow Top Handle, ARCA Top Handle, ARCA Top Plate, and Gimbal Adapter Plates (Freefly Mōvi Pro and DJI Ronin 2) for quick change between handheld and studio modes.Side 3/8-16 ARRI accessory mounts can accept Cage NATO Side Arm (ARRI 3/8-16) for cage building.Product Weight: 438g

MID49 Top Plate (Sony Burano) SKU: M49-CAG-SON-TOP Top Plate (Sony Burano) attaches to the top of the camera and provides 1/4-20 and 3/8-16 threaded holes with ARRI accessory pins, M4x20mm ARRI standard threaded holes, 1/4-20 holes for the Burano's included handle and the optional FX9 control handle. When using the FX9 handle, an upcoming connector bridge will be available from MID49 and attach to the rear opening on the top plate. Center ARCA dovetail clamp allows for attachment of the ARCA Top Handle, ARCA Top Plate, and Gimbal Adapter Plates for quick change between handheld and studio modes. Side 3/8-16 ARRI accessory mounts can accept Cage NATO Side Arm (ARRI 3/8-16) for cage building. Burano tape hook and cable guide can be removed and installed on the top plate.

MID49 Top Plate For Canon C400 SKU: M49-CAG-CC4-TOP Top Plate (Canon C400) attaches to the top of the camera and provides 1/4-20 and 3/8-16 threaded holes with ARRI accessory pins, M4x20mm ARRI standard threaded holes, and includes an adapter for attaching Canon's original C400 top handle (ARRI 3/8-16 to Canon Striped Rosette / Canon Mic Mount). When not using the adapter for Canon's handle, it can be positioned on the Top Plate to provided mounting points for Canon's included microphone shock mount.Additional ARRI 3/8-16 to Canon Striped Rosette / Canon Mic Mounts are available if needed. The Top Plate's center ARCA dovetail clamp allows for attachment of the the Rainbow Handle Kit, ARCA Top Handle, ARCA Top Plate, and Gimbal Adapter Plates (Freefly Mōvi Pro and DJI Ronin 2) for quick change between handheld and studio modes. Side 3/8-16 ARRI accessory mounts can accept Cage NATO Side Arm (ARRI 3/8-16) for cage building.

MID49 Top Plate Handle Adapter (Sony Burano to FX9)SKU: M49-CAG-SON-TPA-FX9 Top Plate Handle Adapter (Sony Burano to FX9) bridges the gap between the camera body and the FX9 handle when using the Top Plate (Sony Burano). Installs by 4x M3 screws into the marked area on the Top Plate. All signals pass through without modification so every function of the FX9 handle is maintained. Weight: 30gDimensions: 36 x 53 x 26mm

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew

MID49 TWIST Mount EVF KitTWIST Mount EVF Kit with Knuckle includes the Double Sided NATO Rail to 15mm Rod which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately).The NATO rail has built in variable friction via the thumbscrew and safety pins are on each end to prevent accidental accessory removal.Included TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. TWIST Mount EVF Kit with Knuckle Onlyincludes the NATO rail and Knuckle described aboveTWIST Mount EVF Kit for Canon C400, C300mkIII, C500mkII, LM-V2includes the NATO rail, Knuckle, and Canon Monitor SpudWorks with Canon C400, C300mkIII, C500mkII, and LM-V2TWIST Mount EVF Kit with ARRI M6 Rosetteincludes the NATO rail, Knuckle, and male ARRI M6 Rosette SpudWorks with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVFWorks with Z CAM 2.89" EVF101Works with original PORTKEYS OEYEFor Kinefinity Eagle SDI, a 1/4-20 version is required.TWIST Mount EVF Kit with ARRI 1/4-20includes the NATO rail, Knuckle, and male ARRI 1/4-20 SpudWorks with Blackmagic Design PYXIS MonitorWorks with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with ARRI Camera Control Monitor CCM-1Works with PORTKEYS LH7P (be careful, the monitor is plastic)TWIST Mount EVF Kit with ARRI 3/8-16includes the NATO rail, Knuckle, and male ARRI 3/8-16 SpudWorks with Atomos Shogun Monitor-Recorder (ATOMSHG002)TWIST Mount EVF Kit with Sony 1/4-20includes the NATO rail, Knuckle, and male Sony 1/4-20 SpudWorks with Sony Burano directly and also the EVF Pivot AdapterTWIST Mount EVF Kit with L Bracket 1/4-20includes the NATO rail, Knuckle, and L Bracket with 1/4-20 screwsWorks with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions)Works with original RED DSMC1 EVFTWIST Mount EVF Kit with Female ARRI 1/4-20includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 1/4-20 product including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center)TWIST Mount EVF Kit with Female ARRI 3/8-16includes the NATO rail, Knuckle, and female ARRI 1/4-20 SpudWorks with any 3/8-16 product including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)TWIST Mount EVF Combo Kitincludes the NATO rail, Knuckle, and ARRI M6 Rosette, ARRI 1/4-20, ARRI 3/8-16, L Bracket 1/4-20, Female ARRI 1/4-20, Female ARRI 3/8-16Note this does not include the specific Canon and Sony attachments TWIST Mount EVF Kit with Blackmagic Viewfinder WedgeIncludes the NATO rail, Knuckle, and Blackmagic Viewfinder Wedge Spud, which can attach to a sideways 15mm rod clamp like the optional items Multi-Function Rod Bracket (MFRB 15mm LW), Single 15mm Rod Clamp (M4 x 20mm), or Canon 1/4-20 Striped Rosette 15mm Rod Clamp (sold separately)The NATO rail has built-in variable friction via the thumbscrew, and safety pins are on each end to prevent accidental accessory removalIncluded TWIST Mount EVF Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew