Mole Richardson Senior Windmachine Low Stand Type 19720

Mole Richardson 18” Windmachine Moleffect Type 6971 This Mole Richardson 18” Windmachine can now be operated manually or off a DMX Control Console along with all your other lights and special effects. With Mole Richardson´s new built-in DMX control panel you can daisy chain and signature many windmachines and control them in multiple combinations from a DMX Control Console. This unit can be operated with 120 or 240 volts A.C. or D.C. current and is designed to create maximum air-flow with minimum noise for Hollywood sound stage use. A solid state control varies the speed  of the fan to produce wind effects from a light zephyr to a stiff breeze. This Mole Richardson Moleffect is useful not only for routine wind effects, but also for dispersing snow flakes, creating a localized dusty breeze, etc. Radial vanes columnate air-stream, vanes may be removed for wide dispersion. At high speed the fan may be used to cool or ventilate a set or to clear smoke. The unit sets on the floor or mounts on a stand. Equipped with a Roll Bar for ease of handling Windmachine Moleffect SPECIFICATIONS WINDMACHINE: Mole Richardson Type 6971RATING: 120/240 volts, A.C. or D.C., 5 amps maxVOLUME: 2390 cubic ft. per minuteAIR VELOCITY: 1700 ft. per minuteMOTOR: 1/3 H.P., D.C. brushless, totally enclosed, ball bearing, solid base, variable speed motor, mounted to housing by rubber flex-bolt mountsSWITCH: Toggle switch with “OFF-ON” plate mounted on operating side of housingCABLE: Attached 7.62 m, Type SO, 3 conductor #16 AWG (when ordering specify type of plug required)CONTROL KNOB: Regulate fan speed, mounted on operating side of housing. Speed indicator dial numbered 1 through 10ELECTRONIC MOTOR CONTROL MODULE:Mounted below motor supportFAN: Three-blade, 45.72 cm diameterGUARDS: Welded steel wireAIR GUIDE: Aluminum radial vanes columnate air flowCONSTRUCTION: Sheet steel housing and steel wire guardsROLL BAR: Tubular steelYOKE: Tubular steel with removable 2,86 cm dia. steel yoke pinDMX CONTROL PANEL: Built in—Used to decode the incoming digital signal (DMX) to 0-10V D.C. OutputINPUT CONNECTOR: 5-pinOUTPUT CONNECTOR TO NEXT DMX MODULE: 5-pinSIZE: 66,66 cm diameter, 50.8 cm lengthFINISH: Maroon Powder Coat Enamel and Electroplated GuardsWINDMACHINE WEIGHT: 40.6 kg

Mole Richardson 12” Windmachine Moleffect Type 7971 This Mole Richardson 12” Windmachine can now be operated manually or off a DMX Control Console along with all your other lights and special effects. With the Mole Richardson´s new built-in DMX control panel you can daisy chain and signature many windmachines and control them in multiple combinations from a DMX Control Console. This unit can be operated with 120 or 240 volts A.C. or D.C. current and is designed to create maximum air-flow with minimum noise for Hollywood sound stage use. A solid state control varies the speed of the fan to produce wind effects from a light zephyr to a stiff breeze. This Mole Richardson Windmachine is useful not only for routine wind effects, but also for dispersing snowflakes, creating a localized dusty breeze, etc. Radial vanes columnate air-stream, vanes may be removed for wide dispersion. At high speed the fan may be used to cool or ventilate a set or to clear smoke. The unit sets on the floor or mounts on a stand. Equipped with a Roll Bar for ease of handling. Windmachine Moleffect SPECIFICATIONS WINDMACHINE: Mole Richardson Type 7971RATING: 120/240 volts, A.C. or D.C., 5 amps maxVOLUME: 1510 cubic ft. per minuteAIR VELOCITY: 2400 ft. per minuteMOTOR: D.C. brushless, totally enclosed, ball bearing, solid base, variable speed motor, mounted to housing by rubber flex-bolt mountsSWITCH: Toggle switch with "OFF-ON" plate mounted on operating side of housingCABLE: Attached 7.62 m, Type SO, 3 conductor #16 AWG (when ordering specify type of plug required)CONTROL KNOB: Regulate fan speed, mounted on operating side of housing. Speed indicator dial numbered 1 through 10ELECTRONIC MOTOR CONTROL MODULE: Mounted below motor supportFAN: Three-blade, 12 inch diameterGUARDS: Welded steel wireAIR GUIDE: Aluminum radial vanes columnate air flowCONSTRUCTION: Sheet steel housing and steel wire guardsROLL BAR: Tubular steelYOKE: Tubular steel with removable 2.86 cm dia. steel yoke pinDMX CONTROL PANEL: Built in—Used to decode the incoming digital signal (DMX) to 0-10V D.C. OutputINPUT CONNECTOR: 5-pinOUTPUT CONNECTOR TO NEXT DMX MODULE: 5-pinFINISH: Maroon Powder Coat Enamel and Electroplated GuardsSIZE: 53.34 cm diameter, 46.99 cm lengthWINDMACHINE WEIGHT: 24.49 kg