MID49 TWIST Ball Monitor Mount (ARRI 1/4-20 + ARRI 3/8-16 Spuds)

MID49 TWIST Ball Monitor MountTWIST Ball Monitor Mount is an articulating arm with interchangeable mounting spuds that utilize a variable friction 15mm clamp. With the variable friction design, you can grab and twist the arm or monitor without loosening a thumbscrew. Install the bottom spud on your camera or cheeseplate and the top spud on your monitor or accessory, then slip the TWIST Balls into place and lock the thumbscrews.The Speedball Clamp's "Chip Clip" design allows for easy, annoyance-free installation, and the ratcheting thumbscrew can be pulled out and repositioned. 3, 6, and 9-inch arm kits include the Speedball Extension, a second Speedball Clamp, and a hook and loop cable tie. TWIST Ball components are compatible with our Universal Speedball and any other brand of 1-inch (25mm) ball attachment like Ultralight Control Systems, Wooden Camera, etc.Choose your SpudsNo SpudA 15mm friction hole with no mounting spudARRI 1/4-20ARRI 1/4-20 with removable 3mm locating pins 10.4mm center to center       Second set of holes for 3mm pins 15mm center to center       Works with any cheese plate or accessory with ARRI standard 1/4-20 holes       Works with Blackmagic Design PYXIS Monitor       Works with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5       Works with ARRI Camera Control Monitor CCM-1ARRI 3/8-16ARRI 3/8-16 with removable 3mm locating pins 15mm center to center        Works with any cheese plate or accessory with ARRI standard 3/8-16 holes       Works with Atomos Shogun Ultra Monitor-Recorder (ATOMSHG002)Canon C400, C300mkIII, C500mkII, LM-V2Works with Canon C400, C300mkIII, C500mkII, and LM-V2ARRI M6 RosetteWorks with Z CAM 2.89" EVF101       Works with original PORTKEYS OEYESony / PortKeys 1/4-20   Attaches to any of the Sony cameras with Sony locating pins like Burano, FX6, and FX9       Works with Sony Burano EVF Pivot Adapter        Works with PORTKEYS LH7P (be careful, the monitor is plastic)       Works with PORTKEYS 5” BM5 IVL Bracket 1/4-20       Includes the slotted L Bracket with two 1/4-20 screws       Works with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions       Works with original RED DSMC1 EVFFemale ARRI 1/4-20        Works with any 1/4-20 product, including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center) Female ARRI 3/8-16      Works with any 3/8-16 product, including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)  1/4-20 Rosette      Works with 1/4-20 Rosette on the Kinefinity EAGLE SDI (or HDMI) e-Viewfinder       Works with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVF       This is NOT a regular ARRI rosette    Old-Style SmallHD 1/4-20       Older style SmallHD 1/4-20 with wide locating tabs       Works with legacy 5" SmallHD monitors like 501, 502, Focus 5, Focus Bolt, Action 5        Works with legacy 7" SmallHD monitors like 701, 702, Focus 7, Indie 7, Cine 7  ARRI Viewfinder Wedge      Works with ARRI standard EVF wedge products like EVF-1, EVF-2, MVF-1, MVF-2      Works with other ARRI wedge adapters like ARRI VFA-4, K2.0015520, etc.      Works with 3rd party products that utilize ARRI-style mounting wedges.   Blackmagic Viewfinder Wedge        Includes the NATO rail, Knuckle, and spud for Blackmagic Design dovetail wedges        Works with URSA Cine EVF - CINEURSAB/EVF       Works with URSA Cine EVF Extension - CINEURSAB/EVFEXT       Works with PYXIS Monitor Kit - CINEURSABB/AMKIT   Action Cameras (GoPro‚ DJI Osmo Action‚ Insta360)       Standard receptacle for 2-prong action camera feet       Works with GoPro, DJI Osmo Action, Insta360       Works with many other 3rd party action camera products  Sony FX6      Attaches to the FX6 monitor to provide a rigid "flop stop" mount = Monitor folding capability is maintained   Male Hot Shoe      Clamps to standard camera shoe mounts   Female Hot Shoe      Female shoe receptacle for standard shoe accessories    NATO Rail       Standard NATO rail with safety pins on each end       Mounting area between pins is 30mm  NATO Clamp       Standard NATO clamp with ratcheting thumbscrew       Clamping area between outside edges 21mm     Tripod Expansion Adapter        Includes a 5mm locating pin and 1/4-20 screw for attaching small cameras with a standard "tripod" mount      Remove the locating pin and screw this adapter into any two 1/4-20 threaded holes between 16.5 and 33mm center to center Threaded ARRI 1/4-20 and 3/8-16 holes also available

MID49 TWIST Ball Monitor MountTWIST Ball Monitor Mount is an articulating arm with interchangeable mounting spuds that utilize a variable friction 15mm clamp. With the variable friction design, you can grab and twist the arm or monitor without loosening a thumbscrew. Install the bottom spud on your camera or cheeseplate and the top spud on your monitor or accessory, then slip the TWIST Balls into place and lock the thumbscrews.The Speedball Clamp's "Chip Clip" design allows for easy, annoyance-free installation, and the ratcheting thumbscrew can be pulled out and repositioned. 3, 6, and 9-inch arm kits include the Speedball Extension, a second Speedball Clamp, and a hook and loop cable tie. TWIST Ball components are compatible with our Universal Speedball and any other brand of 1-inch (25mm) ball attachment like Ultralight Control Systems, Wooden Camera, etc.Choose your SpudsNo SpudA 15mm friction hole with no mounting spudARRI 1/4-20ARRI 1/4-20 with removable 3mm locating pins 10.4mm center to center       Second set of holes for 3mm pins 15mm center to center       Works with any cheese plate or accessory with ARRI standard 1/4-20 holes       Works with Blackmagic Design PYXIS Monitor       Works with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5       Works with ARRI Camera Control Monitor CCM-1ARRI 3/8-16ARRI 3/8-16 with removable 3mm locating pins 15mm center to center        Works with any cheese plate or accessory with ARRI standard 3/8-16 holes       Works with Atomos Shogun Ultra Monitor-Recorder (ATOMSHG002)Canon C400, C300mkIII, C500mkII, LM-V2Works with Canon C400, C300mkIII, C500mkII, and LM-V2ARRI M6 RosetteWorks with Z CAM 2.89" EVF101       Works with original PORTKEYS OEYESony / PortKeys 1/4-20   Attaches to any of the Sony cameras with Sony locating pins like Burano, FX6, and FX9       Works with Sony Burano EVF Pivot Adapter        Works with PORTKEYS LH7P (be careful, the monitor is plastic)       Works with PORTKEYS 5” BM5 IVL Bracket 1/4-20       Includes the slotted L Bracket with two 1/4-20 screws       Works with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions       Works with original RED DSMC1 EVFFemale ARRI 1/4-20        Works with any 1/4-20 product, including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center) Female ARRI 3/8-16      Works with any 3/8-16 product, including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)  1/4-20 Rosette      Works with 1/4-20 Rosette on the Kinefinity EAGLE SDI (or HDMI) e-Viewfinder       Works with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVF       This is NOT a regular ARRI rosette    Old-Style SmallHD 1/4-20       Older style SmallHD 1/4-20 with wide locating tabs       Works with legacy 5" SmallHD monitors like 501, 502, Focus 5, Focus Bolt, Action 5        Works with legacy 7" SmallHD monitors like 701, 702, Focus 7, Indie 7, Cine 7  ARRI Viewfinder Wedge      Works with ARRI standard EVF wedge products like EVF-1, EVF-2, MVF-1, MVF-2      Works with other ARRI wedge adapters like ARRI VFA-4, K2.0015520, etc.      Works with 3rd party products that utilize ARRI-style mounting wedges.   Blackmagic Viewfinder Wedge        Includes the NATO rail, Knuckle, and spud for Blackmagic Design dovetail wedges        Works with URSA Cine EVF - CINEURSAB/EVF       Works with URSA Cine EVF Extension - CINEURSAB/EVFEXT       Works with PYXIS Monitor Kit - CINEURSABB/AMKIT   Action Cameras (GoPro‚ DJI Osmo Action‚ Insta360)       Standard receptacle for 2-prong action camera feet       Works with GoPro, DJI Osmo Action, Insta360       Works with many other 3rd party action camera products  Sony FX6      Attaches to the FX6 monitor to provide a rigid "flop stop" mount = Monitor folding capability is maintained   Male Hot Shoe      Clamps to standard camera shoe mounts   Female Hot Shoe      Female shoe receptacle for standard shoe accessories    NATO Rail       Standard NATO rail with safety pins on each end       Mounting area between pins is 30mm  NATO Clamp       Standard NATO clamp with ratcheting thumbscrew       Clamping area between outside edges 21mm     Tripod Expansion Adapter        Includes a 5mm locating pin and 1/4-20 screw for attaching small cameras with a standard "tripod" mount      Remove the locating pin and screw this adapter into any two 1/4-20 threaded holes between 16.5 and 33mm center to center Threaded ARRI 1/4-20 and 3/8-16 holes also available

MID49 TWIST Ball Monitor MountTWIST Ball Monitor Mount is an articulating arm with interchangeable mounting spuds that utilize a variable friction 15mm clamp. With the variable friction design, you can grab and twist the arm or monitor without loosening a thumbscrew. Install the bottom spud on your camera or cheeseplate and the top spud on your monitor or accessory, then slip the TWIST Balls into place and lock the thumbscrews.The Speedball Clamp's "Chip Clip" design allows for easy, annoyance-free installation, and the ratcheting thumbscrew can be pulled out and repositioned. 3, 6, and 9-inch arm kits include the Speedball Extension, a second Speedball Clamp, and a hook and loop cable tie. TWIST Ball components are compatible with our Universal Speedball and any other brand of 1-inch (25mm) ball attachment like Ultralight Control Systems, Wooden Camera, etc.Choose your SpudsNo SpudA 15mm friction hole with no mounting spudARRI 1/4-20ARRI 1/4-20 with removable 3mm locating pins 10.4mm center to center       Second set of holes for 3mm pins 15mm center to center       Works with any cheese plate or accessory with ARRI standard 1/4-20 holes       Works with Blackmagic Design PYXIS Monitor       Works with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5       Works with ARRI Camera Control Monitor CCM-1ARRI 3/8-16ARRI 3/8-16 with removable 3mm locating pins 15mm center to center        Works with any cheese plate or accessory with ARRI standard 3/8-16 holes       Works with Atomos Shogun Ultra Monitor-Recorder (ATOMSHG002)Canon C400, C300mkIII, C500mkII, LM-V2Works with Canon C400, C300mkIII, C500mkII, and LM-V2ARRI M6 RosetteWorks with Z CAM 2.89" EVF101       Works with original PORTKEYS OEYESony / PortKeys 1/4-20   Attaches to any of the Sony cameras with Sony locating pins like Burano, FX6, and FX9       Works with Sony Burano EVF Pivot Adapter        Works with PORTKEYS LH7P (be careful, the monitor is plastic)       Works with PORTKEYS 5” BM5 IVL Bracket 1/4-20       Includes the slotted L Bracket with two 1/4-20 screws       Works with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions       Works with original RED DSMC1 EVFFemale ARRI 1/4-20        Works with any 1/4-20 product, including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center) Female ARRI 3/8-16      Works with any 3/8-16 product, including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)  1/4-20 Rosette      Works with 1/4-20 Rosette on the Kinefinity EAGLE SDI (or HDMI) e-Viewfinder       Works with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVF       This is NOT a regular ARRI rosette    Old-Style SmallHD 1/4-20       Older style SmallHD 1/4-20 with wide locating tabs       Works with legacy 5" SmallHD monitors like 501, 502, Focus 5, Focus Bolt, Action 5        Works with legacy 7" SmallHD monitors like 701, 702, Focus 7, Indie 7, Cine 7  ARRI Viewfinder Wedge      Works with ARRI standard EVF wedge products like EVF-1, EVF-2, MVF-1, MVF-2      Works with other ARRI wedge adapters like ARRI VFA-4, K2.0015520, etc.      Works with 3rd party products that utilize ARRI-style mounting wedges.   Blackmagic Viewfinder Wedge        Includes the NATO rail, Knuckle, and spud for Blackmagic Design dovetail wedges        Works with URSA Cine EVF - CINEURSAB/EVF       Works with URSA Cine EVF Extension - CINEURSAB/EVFEXT       Works with PYXIS Monitor Kit - CINEURSABB/AMKIT   Action Cameras (GoPro‚ DJI Osmo Action‚ Insta360)       Standard receptacle for 2-prong action camera feet       Works with GoPro, DJI Osmo Action, Insta360       Works with many other 3rd party action camera products  Sony FX6      Attaches to the FX6 monitor to provide a rigid "flop stop" mount = Monitor folding capability is maintained   Male Hot Shoe      Clamps to standard camera shoe mounts   Female Hot Shoe      Female shoe receptacle for standard shoe accessories    NATO Rail       Standard NATO rail with safety pins on each end       Mounting area between pins is 30mm  NATO Clamp       Standard NATO clamp with ratcheting thumbscrew       Clamping area between outside edges 21mm     Tripod Expansion Adapter        Includes a 5mm locating pin and 1/4-20 screw for attaching small cameras with a standard "tripod" mount      Remove the locating pin and screw this adapter into any two 1/4-20 threaded holes between 16.5 and 33mm center to center Threaded ARRI 1/4-20 and 3/8-16 holes also available

MID49 TWIST Ball Monitor MountTWIST Ball Monitor Mount is an articulating arm with interchangeable mounting spuds that utilize a variable friction 15mm clamp. With the variable friction design, you can grab and twist the arm or monitor without loosening a thumbscrew. Install the bottom spud on your camera or cheeseplate and the top spud on your monitor or accessory, then slip the TWIST Balls into place and lock the thumbscrews.The Speedball Clamp's "Chip Clip" design allows for easy, annoyance-free installation, and the ratcheting thumbscrew can be pulled out and repositioned. 3, 6, and 9-inch arm kits include the Speedball Extension, a second Speedball Clamp, and a hook and loop cable tie. TWIST Ball components are compatible with our Universal Speedball and any other brand of 1-inch (25mm) ball attachment like Ultralight Control Systems, Wooden Camera, etc.Choose your SpudsNo SpudA 15mm friction hole with no mounting spudARRI 1/4-20ARRI 1/4-20 with removable 3mm locating pins 10.4mm center to center       Second set of holes for 3mm pins 15mm center to center       Works with any cheese plate or accessory with ARRI standard 1/4-20 holes       Works with Blackmagic Design PYXIS Monitor       Works with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5       Works with ARRI Camera Control Monitor CCM-1ARRI 3/8-16ARRI 3/8-16 with removable 3mm locating pins 15mm center to center        Works with any cheese plate or accessory with ARRI standard 3/8-16 holes       Works with Atomos Shogun Ultra Monitor-Recorder (ATOMSHG002)Canon C400, C300mkIII, C500mkII, LM-V2Works with Canon C400, C300mkIII, C500mkII, and LM-V2ARRI M6 RosetteWorks with Z CAM 2.89" EVF101       Works with original PORTKEYS OEYESony / PortKeys 1/4-20   Attaches to any of the Sony cameras with Sony locating pins like Burano, FX6, and FX9       Works with Sony Burano EVF Pivot Adapter        Works with PORTKEYS LH7P (be careful, the monitor is plastic)       Works with PORTKEYS 5” BM5 IVL Bracket 1/4-20       Includes the slotted L Bracket with two 1/4-20 screws       Works with PORTKEYS LEYE III (note their HDMI cable may conflict with NATO rail in certain positions       Works with original RED DSMC1 EVFFemale ARRI 1/4-20        Works with any 1/4-20 product, including those with ARRI spaced locating pins (3mm diameter pin on 10.4mm spacing center to center) Female ARRI 3/8-16      Works with any 3/8-16 product, including those with ARRI spaced locating pins (3mm diameter pin on 15mm spacing center to center)  1/4-20 Rosette      Works with 1/4-20 Rosette on the Kinefinity EAGLE SDI (or HDMI) e-Viewfinder       Works with Zacuto Gratical, Gratical Eye, and Kameleon Pro EVF       This is NOT a regular ARRI rosette    Old-Style SmallHD 1/4-20       Older style SmallHD 1/4-20 with wide locating tabs       Works with legacy 5" SmallHD monitors like 501, 502, Focus 5, Focus Bolt, Action 5        Works with legacy 7" SmallHD monitors like 701, 702, Focus 7, Indie 7, Cine 7  ARRI Viewfinder Wedge      Works with ARRI standard EVF wedge products like EVF-1, EVF-2, MVF-1, MVF-2      Works with other ARRI wedge adapters like ARRI VFA-4, K2.0015520, etc.      Works with 3rd party products that utilize ARRI-style mounting wedges.   Blackmagic Viewfinder Wedge        Includes the NATO rail, Knuckle, and spud for Blackmagic Design dovetail wedges        Works with URSA Cine EVF - CINEURSAB/EVF       Works with URSA Cine EVF Extension - CINEURSAB/EVFEXT       Works with PYXIS Monitor Kit - CINEURSABB/AMKIT   Action Cameras (GoPro‚ DJI Osmo Action‚ Insta360)       Standard receptacle for 2-prong action camera feet       Works with GoPro, DJI Osmo Action, Insta360       Works with many other 3rd party action camera products  Sony FX6      Attaches to the FX6 monitor to provide a rigid "flop stop" mount = Monitor folding capability is maintained   Male Hot Shoe      Clamps to standard camera shoe mounts   Female Hot Shoe      Female shoe receptacle for standard shoe accessories    NATO Rail       Standard NATO rail with safety pins on each end       Mounting area between pins is 30mm  NATO Clamp       Standard NATO clamp with ratcheting thumbscrew       Clamping area between outside edges 21mm     Tripod Expansion Adapter        Includes a 5mm locating pin and 1/4-20 screw for attaching small cameras with a standard "tripod" mount      Remove the locating pin and screw this adapter into any two 1/4-20 threaded holes between 16.5 and 33mm center to center Threaded ARRI 1/4-20 and 3/8-16 holes also available

MID49 TWIST Mount Monitor AdapterTWIST Mount Monitor Right Angle Spud Adapter allows monitors with top and bottom mounting points to be adapted to the TWIST Mount System. The kit includes the right-angle adapter and three lengths of 15mm rod with the TWIST groove on the end: 50mm, 100mm, and 150mm.Choose the appropriate Spud, attach it to the top or bottom of your monitor, select the appropriate length of rod, and install that into the TWIST Mount Knuckle (sold separately).Spud OptionsOld-Style SmallHD 1/4-20Older version SmallHD monitors where locating pins are short and wideWorks with SmallHD Focus 5, Focus Pro for RED, 502, 503, Action 5Works with SmallHD AC7, Indie 7, 702, 703ARRI 1/4-20 (3mm pins spaced 10.4mm apart)Works with Blackmagic Video Assist (remove locating pins)Works with Atomos Shinobi, Ninja, Shogun (remove locating pins)Works with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with TVLogic F-5A, F-7H, F-7HS (remove locating pins)ARRI 3/8-16 (3mm pins spaced 15mm apart)Works with Atomos Shogun Ultra Monitor-Recorder (ATOMSHG002)Sony / PortKeys 1/4-20Works with PORTKEYS BM5 IV, BM5 IV WR, LH5P II Works with PORTKEYS PT5 II, PT6Works with PORTKEYS LH7P, LH7H, HD7HWorks with PORTKEYS BM7 II DS U, HS8

MID49 TWIST Mount Monitor AdapterTWIST Mount Monitor Right Angle Spud Adapter allows monitors with top and bottom mounting points to be adapted to the TWIST Mount System. The kit includes the right-angle adapter and three lengths of 15mm rod with the TWIST groove on the end: 50mm, 100mm, and 150mm.Choose the appropriate Spud, attach it to the top or bottom of your monitor, select the appropriate length of rod, and install that into the TWIST Mount Knuckle (sold separately).Spud OptionsOld-Style SmallHD 1/4-20Older version SmallHD monitors where locating pins are short and wideWorks with SmallHD Focus 5, Focus Pro for RED, 502, 503, Action 5Works with SmallHD AC7, Indie 7, 702, 703ARRI 1/4-20 (3mm pins spaced 10.4mm apart)Works with Blackmagic Video Assist (remove locating pins)Works with Atomos Shinobi, Ninja, Shogun (remove locating pins)Works with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with TVLogic F-5A, F-7H, F-7HS (remove locating pins)ARRI 3/8-16 (3mm pins spaced 15mm apart)Works with Atomos Shogun Ultra Monitor-Recorder (ATOMSHG002)Sony / PortKeys 1/4-20Works with PORTKEYS BM5 IV, BM5 IV WR, LH5P II Works with PORTKEYS PT5 II, PT6Works with PORTKEYS LH7P, LH7H, HD7HWorks with PORTKEYS BM7 II DS U, HS8

MID49 TWIST Mount Monitor AdapterTWIST Mount Monitor Right Angle Spud Adapter allows monitors with top and bottom mounting points to be adapted to the TWIST Mount System. The kit includes the right-angle adapter and three lengths of 15mm rod with the TWIST groove on the end: 50mm, 100mm, and 150mm.Choose the appropriate Spud, attach it to the top or bottom of your monitor, select the appropriate length of rod, and install that into the TWIST Mount Knuckle (sold separately).Spud OptionsOld-Style SmallHD 1/4-20Older version SmallHD monitors where locating pins are short and wideWorks with SmallHD Focus 5, Focus Pro for RED, 502, 503, Action 5Works with SmallHD AC7, Indie 7, 702, 703ARRI 1/4-20 (3mm pins spaced 10.4mm apart)Works with Blackmagic Video Assist (remove locating pins)Works with Atomos Shinobi, Ninja, Shogun (remove locating pins)Works with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with TVLogic F-5A, F-7H, F-7HS (remove locating pins)ARRI 3/8-16 (3mm pins spaced 15mm apart)Works with Atomos Shogun Ultra Monitor-Recorder (ATOMSHG002)Sony / PortKeys 1/4-20Works with PORTKEYS BM5 IV, BM5 IV WR, LH5P II Works with PORTKEYS PT5 II, PT6Works with PORTKEYS LH7P, LH7H, HD7HWorks with PORTKEYS BM7 II DS U, HS8

MID49 TWIST Mount Monitor AdapterTWIST Mount Monitor Right Angle Spud Adapter allows monitors with top and bottom mounting points to be adapted to the TWIST Mount System. The kit includes the right-angle adapter and three lengths of 15mm rod with the TWIST groove on the end: 50mm, 100mm, and 150mm.Choose the appropriate Spud, attach it to the top or bottom of your monitor, select the appropriate length of rod, and install that into the TWIST Mount Knuckle (sold separately).Spud OptionsOld-Style SmallHD 1/4-20Older version SmallHD monitors where locating pins are short and wideWorks with SmallHD Focus 5, Focus Pro for RED, 502, 503, Action 5Works with SmallHD AC7, Indie 7, 702, 703ARRI 1/4-20 (3mm pins spaced 10.4mm apart)Works with Blackmagic Video Assist (remove locating pins)Works with Atomos Shinobi, Ninja, Shogun (remove locating pins)Works with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with TVLogic F-5A, F-7H, F-7HS (remove locating pins)ARRI 3/8-16 (3mm pins spaced 15mm apart)Works with Atomos Shogun Ultra Monitor-Recorder (ATOMSHG002)Sony / PortKeys 1/4-20Works with PORTKEYS BM5 IV, BM5 IV WR, LH5P II Works with PORTKEYS PT5 II, PT6Works with PORTKEYS LH7P, LH7H, HD7HWorks with PORTKEYS BM7 II DS U, HS8

MID49 TWIST Mount Monitor KnuckleTWIST Mount Monitor Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. The Right Angle Spud Adapter allows monitors without side mounting points to be adapted to the TWIST Mount system and includes three lengths of 15mm rod with the TWIST groove on the end: 50mm, 100mm, and 150mm.Choose the appropriate Spud screw type, attach it to the top or bottom of your monitor, choose the appropriate length of rod, and install into the TWIST Knuckle.Spud OptionsOld-Style SmallHD 1/4-20Older version SmallHD monitors where locating pins are short and wideWorks with SmallHD Focus 5, Focus Pro for RED, 502, 503, Action 5Works with SmallHD AC7, Indie 7, 702, 703ARRI 1/4-20 (3mm pins spaced 10.4mm apart)Works with Blackmagic Video Assist (remove locating pins)Works with Atomos Shinobi, Ninja, Shogun (remove locating pins)Works with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with TVLogic F-5A, F-7H, F-7HS (remove locating pins)ARRI 3/8-16 (3mm pins spaced 15mm apart)Works with Atomos Shogun Ultra Monitor-Recorder (ATOMSHG002)Sony / PortKeys 1/4-20Works with PORTKEYS BM5 IV, BM5 IV WR, LH5P IIWorks with PORTKEYS PT5 II, PT6Works with PORTKEYS LH7P, LH7H, HD7HWorks with PORTKEYS BM7 II DS U, HS8

MID49 TWIST Mount Monitor KnuckleTWIST Mount Monitor Knuckle has a NATO clamp on one end and a variable friction 15mm mount on the other. With the variable friction design, you can grab and twist the monitor without loosening the thumbscrew. The Right Angle Spud Adapter allows monitors without side mounting points to be adapted to the TWIST Mount system and includes three lengths of 15mm rod with the TWIST groove on the end: 50mm, 100mm, and 150mm.Choose the appropriate Spud screw type, attach it to the top or bottom of your monitor, choose the appropriate length of rod, and install into the TWIST Knuckle.Spud OptionsOld-Style SmallHD 1/4-20Older version SmallHD monitors where locating pins are short and wideWorks with SmallHD Focus 5, Focus Pro for RED, 502, 503, Action 5Works with SmallHD AC7, Indie 7, 702, 703ARRI 1/4-20 (3mm pins spaced 10.4mm apart)Works with Blackmagic Video Assist (remove locating pins)Works with Atomos Shinobi, Ninja, Shogun (remove locating pins)Works with recent SmallHD monitors like Indie 5, Cine 5, and Ultra 5Works with TVLogic F-5A, F-7H, F-7HS (remove locating pins)ARRI 3/8-16 (3mm pins spaced 15mm apart)Works with Atomos Shogun Ultra Monitor-Recorder (ATOMSHG002)Sony / PortKeys 1/4-20Works with PORTKEYS BM5 IV, BM5 IV WR, LH5P IIWorks with PORTKEYS PT5 II, PT6Works with PORTKEYS LH7P, LH7H, HD7HWorks with PORTKEYS BM7 II DS U, HS8