Blackmagic URSA Cine 12K LF Body

MID49 Power Distribution Box DB-12 (Blackmagic URSA Cine, V-Mount High Voltage)Power Distribution Box DB-12 (Blackmagic URSA Cine, V-Mount High Voltage) attaches directly to the camera body using five M3 screws and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors.The included USB-C cable can be installed inside DB-12 and connected to the top-rear port on the camera body to enable remote start/stop capability using 3-pin Fischer devices. =Hot-swap between on-board battery and 8pin LEMO compatible connector without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 22.8V at which point, the DB-12 will switch to an onboard battery.With the SMART FUSE design, camera power is monitored, and the remaining power budget is allocated to accessories. For example, the URSA Cine uses approximately 4.8A at 28V, so when using a 10A capable battery, the remaining 5.2A is allocated for accessory use. If an accessory configuration exceeds the 5.2A limit, accessory power is cut off, leaving the camera powered. The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 5.2A, the RESET button can be pressed, and power will be re-enabled to accessory outputs.In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.INPUTSBATT V-Mount High Voltage PlateDC IN 8pin (21-34V)OUTPUTS2x D-Tap (15V regulated)2x 3pin (battery voltage with run/stop)2x 2pin (15V regulated)1x USB-C PD (5V at 3A with thread lock)Also available in a Gold Mount and B-Mount versions.COMPATIBLE CAMERA MODELSURSA Cine 12K LFURSA Cine 17K 65URSA Cine ImmersiveCOMPATIBLE BATTERIESThis product is only compatible with newer Core HIGH VOLTAGE V-Mount batteries, which are listed below and have a current rating of 10A at 28V.HLX-9MXS Core SWX Helix Max 98WhHLX-150MXS Core SWX Helix Max 147WhHLX-275MXV Core SWX Helix Max 275HLX-360MXV Core SWX Helix Max 360HLX-99UMXV Core SWX Helix Max Ultra 99WhHLX-160UMXV Core SWX Helix Max Ultra 156WhHLX-300UMXV Core SWX Helix Max Ultra 297WhHLX-400UMXV Core SWX Helix Max Ultra 395WhAPX-360HV Core SWX APEX 360 High Voltage

MID49 Power Distribution Box DB-12 (URSA Cine, B-Mount)SKU: M49-DB12-BPower Distribution Box DB-12 (Blackmagic URSA Cine, B-Mount) attaches directly to the camera body using five M3 screws and provides intelligent power distribution with D-Taps, 5V USB-C PD, 3pin Fischers, and 2pin LEMO compatible connectors.The included USB-C cable can be installed inside DB-12 and connected to the top-rear port on the camera body to enable remote start/stop capability using 3-pin Fischer devices. Hot-swap between on-board battery and 8pin LEMO compatible connector without losing camera or accessory power. When both sources are connected, the DC INPUT takes priority down to 22.8V at which point, the DB-12 will switch to an onboard battery.With the SMART FUSE design, camera power is monitored, and the remaining power budget is allocated to accessories. For example, the URSA Cine uses approximately 4.8A at 28V, so when using a 10A capable battery, the remaining 5.2A is allocated for accessory use. If an accessory configuration exceeds the 5.2A limit, accessory power is cut off, leaving the camera powered.The "SMART FUSE" LED will illuminate, showing the error, and once the configuration has been adjusted to lower than 5.2A, the RESET button can be pressed, and power will be re-enabled to accessory outputs. In the event of a complete short circuit, the system will immediately shut down and can only be turned back on once the short circuit has been removed.INPUTSBATT: B-Mount PlateDC IN: 8pin (21-34V)OUTPUTS2x D-Tap (15V regulated)2x 3pin (battery voltage with run/stop)2x 2pin (15V regulated)1x USB-C PD (5V at 3A with thread lock) Also available in a Gold Mount and V-Mount versionsCOMPATIBLE CAMERA MODELSURSA Cine 12K LFURSA Cine 17K 65URSA Cine ImmersiveCOMPATIBLE BATTERIESThis product is compatible with any B-Mount battery capable of 28VINCOMPATIBLE BATTERIESStandard 14.4V batteries will NOT power the camera system. Note that the CORE Maverick Block Battery uses a voltage boost converter to get to 28V and introduces an immense amount of noise into the system, so much so that the DB-12 cannot validate it as a reliable source while an on-board battery is connected. Maverick batteries can only be used when it is the first power source connected.MV6 Core SWX Maverick Block Battery

MID49 Top Plate (Blackmagic URSA Cine LF)SKU: M49-CAG-BMUC-TOPTop Plate (Blackmagic URSA Cine LF) attaches to the top of the camera and provides 1/4-20 and 3/8-16 threaded holes with ARRI accessory pins, M4x20mm ARRI standard threaded holes, and provides ventilation for the URSA fan system. Center ARCA dovetail clamp allows for attachment of the Rainbow Handle Kit, ARCA Top Handle, ARCA Top Plate, and Gimbal Adapter Plates (Freefly Mōvi Pro and DJI Ronin 2) for quick change between handheld and studio modes. Side 3/8-16 ARRI accessory mounts can accept Cage NATO Side Arm (ARRI 3/8-16, 135mm) for cage building.Dimensions (WxLxH): 144 x 191 x 23.8mm

MID49 Base Kit for Blackmagic URSA Cine LFSKU: M49-KTB-BMD-UCLF Base Kit for Blackmagic URSA Cine LF is an accessory kit that includes:Top Plate (Blackmagic URSA Cine LF)Provides 1/4-20 and 3/8-16 threaded holes with ARRI accessory pins, M4x20mm ARRI standard threaded holes, and ventilation holes for the URSA fanARCA Top HandleSliding camera handle that has 1/4-20, 3/8-16 with ARRI locating pins, and M4x20mm threaded holes plus two hot shoe mountsRod Bracket (15mm LW)Attaches to the front of the Top Handle to provide 15mm LW rod supportBaseline 15mm LW (Blackmagic URSA Cine LF)Quick-release 15mm LW baseplate with ARCA Swiss camera dovetail interface on top and ARRI standard dovetail interface on the bottom

PATONA Platinum B-Mount battery with 290Wh 10.1Ah incl. USB-C PD60W input and output 2x D-Tap 16V Discover the latest innovation in our PATONA Platinum series: the B-Mount batteries. Equipped with advanced cell technology, these batteries offer outstanding performance and reliability for the highest demands. Their powerful protection circuits continuously monitor cell balance, temperature, overcharging, and over-discharging to ensure maximum safety and operational efficiency.The integrated OLED display provides a clear overview of the remaining capacity, keeping you well informed at all times. With the versatile D-Tap output, you can easily connect lights and other external devices. The USB-A and USB-C ports allow you to conveniently charge smartphones, tablets, and other devices.A highlight of the Platinum B-Mount battery is its integrated power bank function. Charge devices up to 60W and enjoy the freedom of mobile power supply.By pressing the Power-Check button twice, you activate the LED light on the back of the battery, making the B-Mount plate easily visible even in dark production environments. Pressing the Power-Check button twice again turns the light off, giving you full control over the lighting at all times. This thoughtful feature optimizes handling and ensures you can work efficiently even under challenging conditions.Technical DataVoltage: 28.8 VoltsCapacity: 10.1Ah / 290WhConstant Load: 250W, 10AMaximum Charging Current: 165W, 5AFast Charging: 100W, 3ACell Type: Li-IonNumber of Cells: 24x 18650GAIntegrated LED LightD-Tap 2x Output Voltage: max. 50W, 16V/3.1AUSB-C Port Input: PD 60W, 15V/20V (Max.) 3A -> 5.5h charging time to 100%USB-C Port Output: 60W, 5V/9V/12V/15V/20V (Max.) 3A, BC1.2, PD2.0/3.0, QC2.0/3.0, FCP, SCPUSB-A Port: 10W, 5V/2ACharging Temperature Range: 0 - 40°C Discharge Temperature: -20 - 50°CWeight: 1484gSize: 143 x 101 x 70 mmThe battery is compatible with the following modelsBlackmagic URSA CineARRI ALEXA 35

MID49 Mid Kit for Blackmagic URSA Cine LFSKU: M49-KTM-BMD-UCLFMid Kit for Blackmagic URSA Cine LF is an accessory kit that includesTop Plate (Blackmagic URSA Cine LF)Provides 1/4-20 and 3/8-16 threaded holes with ARRI accessory pins, M4x20mm ARRI standard threaded holes, and ventilation holes for the URSA fan. Also works on the URSA Cine Immersive CameraRainbow Handle Kit (Black)Rainbow Handle Kit is a modular handle system that can be configured in a variety of ways, including down behind the battery, commonly referred to as a Hollywood or Panavision-style handle. Multi-Function Rod Bracket (MFRB 15mm LW) is included in the kit and has lightweight spaced 15mm rod openings which run front to back, and a sideways 15mm rod opening allows users to attach viewfinder mounts or microphone shockmounts2x Cage NATO Side Arm (ARRI 3/8-16, 135mm)Attaches to the sides of the Top Plate and provides an ARRI Rosette adjustable NATO accessory rail with safety pins on each endBaseline 15mm LW (Blackmagic URSA Cine LF)Quick-release 15mm LW baseplate with ARCA Swiss camera dovetail interface on top and ARRI standard dovetail interface on the bottom. Also works on the URSA Cine Immersive Camera2x 15mm Rod (9 inch)Stainless steel iris rods

MID49 Top 15mm Rod Bracket (Sony Burano, Canon C400, Blackmagic PYXIS / URSA Cine LF)SKU: M49-TOP-ROD-15LWTop 15mm Rod Bracket (Sony Burano, Canon C400, Blackmagic PYXIS / URSA Cine LF) attaches to the front of the Top Plates for the listed cameras and holds two 15mm LW rods for adding focus motors, viewfinder mounts, and other accessories over the lens area. Rods pass over the Top Plate and around the ARCA Top Handle and Rainbow Handle while still allowing access for carrying. Great for leaving rod accessories installed when switching to gimbal mode using adapters like Gimbal Top ARCA Adapter (DJI Ronin 2) or (Freefly Mōvi Pro) or the ARCA Top Plate.Compatible Top PlatesTop Plate (Canon C400)Top Plate (Sony Burano)Top Plate (Blackmagic PYXIS)Top Plate (Blackmagic URSA Cine LF)

Wooden Camera Base Plate System for Blackmagic URSA Cine 12K/17KSKU: K10037 This system includes a Riser Plate and ARCA Base Plate that keeps your build at the appropriate optical height for mounting accessories in traditional cinema workflows. The Riser Plate facilitates an open design, allowing efficient airflow to the camera.These plates combined are compatible with any bridge plates that use ARRI Standard height. Utilizing the built-in ARCA system, it allows for quick transitions between Steadicam, shoulder, or tripod workflows with Wooden Camera ARCA accessories. Four rod clamps– two on either side of the riser plate– provide powerful friction to prevent torque and rotation from your lens motors.Two included 3/8”-16 screws allow the plate to fasten to the bottom of the camera, while two pins incorporated into the riser plate prevent the riser from twisting, making for a secure connection. The Riser Plate features an intuitive wedge-clamp locking system with a thumb-screw for added security and comes with 3/8”-16 mounting points to attach the Riser Plate. These plates combined are compatible with any bridge plates that use ARRI Standard height such as our 19mm Bridge Plate. Included ItemsRiser Plate for Blackmagic URSA Cine 12K/17KARCA Base PlateSpecificationsWeight: 675.9 gDimensions: 160.6 x 135 x 43.1 mm 

Wooden Camera Top Plate for Blackmagic URSA Cine 12K/17KSKU: A00829The Top Plate designed for the Blackmagic URSA Cine 12K/17K incorporates open ports emphasizing air flow and connectivity. This system securely mounts to the top of the camera using three 1/4”-20 screws down the center of the camera and adds multiple 1/4”-20 and 3/8”-16 mounting points across the top and sides of the plate. The rear mounting point on the Assistant’s Side of the camera allows for a mounting point to add the Top Plate Extension Block, while the front-facing 3/8”-16 mounting points allow users to add accessories like the Front Dual Rod Clamp to secure 15mm rods for accessories like EVF’s or lens motors. With the forward facing 3/8”-16 mounting points, users can add accessories like Bolt-On Rods or a Maxi Rod Light for lens motors. This Top Plate is compatible with the stock Blackmagic URSA handle.SpecificationsWeight: 412.8gDimensions: 160.6 x 135 x 56 mm

Wooden Camera Top Plate System for Blackmagic URSA Cine 12K/17KSKU: K10038The Top Plate System designed for the Blackmagic URSA Cine 12K/17K incorporates open ports emphasizing airflow. It includes the Top Plate, Front Dual Rod Clamp, and Top Plate Extension Block. This system securely mounts to the top of the camera using three 1/4”-20 screws down the center of the camera and adds multiple 1/4”-20 and 3/8”-16 mounting points across the top and sides of the plate.With the front-facing 3/8”-16 mounting points, users can add the included Front Dual Rod Clamp to secure 15mm rods for accessories like EVF’s or lens motors. Forward-facing 3/8”-16 mounting points allow users to add accessories like Bolt-On Rods for lens motors. This Top Plate is compatible with the stock Blackmagic URSA handle.Included ItemsTop Plate Extension Block for Blackmagic URSA Cine 12K/17KTop Plate for Blackmagic URSA Cine 12K/17KTop Plate Dual Rod Clamp - FrontSpecificationsWeight: 675.9 gDimensions: 107 x 65 x 144 mm

Wooden Camera Elite Accessory System for Blackmagic URSA Cine 12K/17KSKU: K10041Optimize the Blackmagic URSA Cine 12K/17K with an accessory system that compliments its design and adds features to efficiently build out the camera without impeding on ports or usability.Riser Plate and ARCA Base PlateThis system starts with a Riser Plate and ARCA Base Plate that keeps your build at the appropriate optical height for mounting accessories in traditional cinema workflows. The Riser Plate facilitates an open design, allowing efficient airflow to the camera. These plates combined are compatible with any bridge plates that use ARRI Standard height. Utilizing the built-in ARCA system, it allows for quick transitions between Steadicam, shoulder, or tripod workflows with Wooden Camera ARCA accessories.Top Plate SystemTo enhance the capabilities of the camera, a Top Plate emphasizing air flow and connectivity is secured to the top of the camera via three ¼”-20 screws along the camera's center mounting points. In addition, a removable 15mm Dual rod clamp allows users to connect items like the Blackmagic EVF or additional 3rd party accessories. The design includes a removable rear extension for additional connecting points to the top plate. This Top Plate is compatible with the stock Blackmagic URSA handle.Ultra HandleThis system also includes an Ultra Handle that allows users to securely hold on to your camera and adds mounting options for additional accessories.Included ItemsRiser Plate for Blackmagic URSA Cine 12K/17KTop Plate for Blackmagic URSA Cine 12K/17KTop Plate Extension Block for Blackmagic URSA Cine 12K/17KUltra Handle (3/8"-16) Standard KitTop Plate Dual Rod Clamp - FrontARCA Base PlateSpecificationsWeight: 1579 gDimensions: 161 x 135 x 96 mm

Wooden Camera Core Accessory System for Blackmagic URSA Cine 12K/17KSKU: K10040Our Core System was designed to provide users with the essentials of connectivity while providing a sturdy foundation for growing their build.Top PlateTo enhance the capabilities of the camera, a Top Plate emphasizing air flow and connectivity is secured to the top of the camera via three 1/4”-20 screws along the camera's center mounting points. In addition, a removable 15mm Dual rod clamp allows users to connect items like the Blackmagic EVF or additional 3rd party accessories. This Top Plate is compatible with the stock Blackmagic URSA handleRiser Plate and ARCA Base PlateThe foundation of this Core System includes a Riser Plate and ARCA Base Plate that keeps your build at the appropriate optical height for mounting accessories in traditional cinema workflows. The Riser Plate facilitates an open design allowing efficient airflow to the camera. With these plates combined, they are compatible with any bridge plates that use ARRI Standard height. Utilizing the built-in ARCA system, it allows for quick transitions between steadicam, shoulder, or tripod workflows with Wooden Camera ARCA accessoriesIncluded ItemsRiser Plate for Blackmagic URSA Cine 12K/17KARCA Base PlateTop Plate for Blackmagic URSA Cine 12K/17KSpecificationsWeight: 1007 gDimensions: 161 x 135 x 96 mm