BLUESHAPE MVQUICK
V-Mount Hot Swap Adapter
MVQUICK is a hot swap system to be installed as a battery interface between the camera (or any other V-lock compatible device) and the battery pack. The main purpose is to allow camera battery replacement without any power interruption through an automatic detection of the battery removal.
Additionally, BLUESHAPE MVQUICK provides an alternative power source of about 21Wh to be used as UPS in case of a sudden power failure or extended power requirements.
MVQUICK Features
About up to 10~15 minutes runtime when used standalone as an UPS backup batteryInstallable on any V-Lock enabled deviceSelf charging through the installed battery, can be charged also on any V-Lock chargersAllow data communication from battery to cameraNEW: enhanced contact protection for safer air transport
Technical data
Nominal Voltage 14.8VVoltage range 10.8V ~ 16.8VNominal Capacity 1.5Ah, 21WhMax. discharge current10ASize 142 mm 83 mm x 50mmWeight 0.49Kg1. LED indicators showing state of charge of internal battery2. Push button for capacity check3. Installation interface for external V-Lock battery4. Output connector (power outlet, to camera)5. Data communication selector to enable or disable battery communication to camera6. D-Tap auxiliary connector7. V-Lock interface for MVQUICK installation
BlueShape MVQUICKAL
Battery Hot Swap system for ARRI ALEXA
MVQUICKAL is a hot-swapping and digital communications interface, with the same features of MVQUICK, to be installed permanently on the back of ALEXA.
The main purpose of this device is to allow battery replacement without power interruption to the camera through an automatic detection of the battery removal.
Best used with BLUESHAPE V-lock batteries, it acts as a digital communication interface allowing direct communication of the battery runtime parameters to the LCD and viewfinder.
Additionally, BlueShape MVQUICKAL provides an alternative power source of about 21Wh to be used as UPS in case of a sudden power failure or extended power requirements.
MVQUICKAL Specifications
About up to 8~10 minutes runtime when used standalone as an UPS backup batteryInstallable on the back side of ALEXA®Self charging through the installed battery, can be charged with a separate charging unitAllow data communication from battery to camera: the state of charge is displayed to the userNEW: enhanced contact protection for safer air transport
In the box
1 x MVQUICKAL1 x ACDC Charging Unit1 x Screw set
Technical data
Nominal Voltage 14.8VVoltage range 10.8V ~ 16.8VNominal Capacity 1.5Ah, 21WhMax. discharge current10ASize 142 mm x 83 mm x 55mmWeight 0.55Kg1. LED indicators showing state of charge of internal battery2. Push button for capacity check3. Installation interface for external V-Lock battery4. Charging socket. Plug the charger here to apply the first full charge session5. D-Tap auxiliary connector6. Installation side to back of the camera7. Special spring loaded output connector (power and data outlet to camera)8. Screw pattern for installation on back of ALEXA
Core SWX JetPack EVO V-Mount auf V-Mount
SKU: EVO-V
Das JetPack EVO ist die nächste Generation der Jetpack-Serie. Kameras mit größeren Sensoren benötigen mehr Strom, ebenso wie eine Vielzahl von On-Board-Zubehör mit zusätzlichem Strombedarf. Der erhöhte Stromverbrauch erfordert zusätzliche Batteriewechsel während einer Produktion. Das Core SWX JetPack EVO verkürzt die Ausfallzeiten mit einem eingebauten 29-Wh-Lithium-Ionen-Akkupack, das 5 Minuten lang eine Stromaufnahme von bis zu 15 A bewältigen kann - genug Zeit, um einen Akkuwechsel vorzunehmen. Zusätzlich zur Backup-Funktion verfügt das EVO über eine "Boost"- oder Akku-Hilfsfunktion, falls Ihr eingebauter Akku nicht in der Lage sein sollte, den erforderlichen Startstrom zu liefern.Eine 4-Zellen-Lithium-Ionen-Patrone wurde entwickelt, um den Strombedarf zu decken, und befindet sich zwischen der Jetpack-Kamera-Befestigung und der vorderen Akkumontageplatte. Das austauschbare Patronensystem stellt die zukünftige Funktionalität sicher, selbst wenn die Batteriezellen der Patrone nachlassen.
Zusätzlich zu den Batterie-Backup- und Boost-Funktionen verfügt der Core SWX EVO über ein hintergrundbeleuchtetes LCD, das die Stromquelle, den Status der Backup-Batterie und die aktuelle Belastung des Kamerasystems anzeigt.
Für die zusätzliche Stromverteilung ist das EVO standardmäßig mit zwei Powertaps ausgestattet, kann aber auch mit einer Vielzahl von Modulen für das System ausgestattet werden. Die Module werden separat verkauft und sind in verschiedenen (Konfigurationen) mit Ausgängen erhältlich, darunter zwei 2-polige LEMO-geregelte 12-V-Ausgänge sowie ein 3-poliger Fischer-24-V-Ausgang. Die Ausgänge sind mechanisch so konstruiert, dass sie die Anschlüsse an einem RED DSMC2 Pro I/O-Modul nicht behindern. Die Module verfügen je nach Typ auch über einen USB5v- und einen 6-poligen LEMO-Stromeingang, falls Sie eine Stromversorgung oder einen Batterieblock zur Verfügung haben.
Der JPE-V lässt sich als Standard-V-Mount montieren und wurde für eine nahtlose Montage an den Kameras an den Formfaktor der Kamera angepasst.
V-Mount auf V-Mount JetPack EVO Merkmale
Eingebauter Akku, der bis zu 15A für 5 Minuten aufnehmen kannHintergrundbeleuchtetes LCDKapazität: 29Wh Größe: 11,61 cm x 9,42 cm x 4,83 cm Gewicht: 0,64 kg Stromeingang: 11-17vdc über Batterieplatte Ausgang: DC 11-17v, ungeregeltBatterie-Backup-Ausgang: DC 11-17v, 15A fähig 2x P-Tap-Ausgänge: DC 11-17v, ungeregelt
Core SWX JP-A-FS7 GOLD Mount Jetpack für Sony PXW-FS7
Das Jetpack bietet alle Leistungsausgänge, die Sie jemals brauchen werden, in einem superkompakten Design. Das JetPack Sony FS7 beinhaltet
Stromanschluss für Ihre Sony FS7TZwei Powertap-Ausgänge (zur Stromversorgung von Monitoren, Lampen usw.)Einen USB-Ausgang (z. B. Redmote, Tascam DR-05, andere USB-Geräte)Ein 5-V-Lemo-Ausgang (z. B. Zoom, AJA)Zwei geregelte 4-polige 12-V-Hirose-Ausgänge (z. B. für HDV-Kameras, DSLRs)Ein 4-poliger XLR-StromeingangHalterung für die Montage des Jetpacks direkt an der Rückseite der Sony FS7 als Alternative zum XDCA-FS7
Das Vollaluminium-Design reduziert das Gewicht und ist dennoch widerstandsfähig. Das JetPack verfügt über drei 1/4-20 Befestigungspunkte sowie eine optionale "Käse"-Rückplatte, die zusätzliche 1/4-20 und 3/8-16 Gewindelöcher bietet.
Switronix JP-A-FS7 Technische Daten
Abmessungen 20,32 cm x 8,89 cm x 4,77 cmGewicht 0,77 kgGOLD-Mount Batterie/4-pin XLR Eingang DC 11-17vFS7 Power Input Pin DC 11-17v, ungeregeltP-Tap(2) AusgängeDC 11-17v, ungeregeltLEMO 2-polig (0B) 5 V, 2,5 AHRS 4-polig12v, 2,5a. Enthält zwei 12-V-AusgängeBefestigungspunkte 1/4-20-Gewinde an der Unterseite und zwei an der RückseiteBefestigungspunkte M3-Schraubenmuster auf der Rückseite für optionale Cheese PlateUSB-Ausgang5V, 1a Das JetPack lädt ein iPad auf, aber langsamer als das Apple-Ladegerät. Auf dem iPad-Bildschirm wird "Not Charging" angezeigt, aber das bedeutet nur, dass das Gerät nicht mit 2,1 A Strom versorgt wird.
Core SWX Lemo JetPack Kabel zu Flugkabeln
24" (60.96 cm) Lemo JetPack Kabel mit Flugkabeln, 12v
JETPACK 12V, 4-PIN LEMO CABLE WITH FLYING LEADS ermöglicht es dem Endverbraucher, seinen eigenen Stecker am anderen Ende für die gewünschte Spannung anzubringen
Core SWX Lemo JetPack Kabel zu Flugkabeln
24" (60.96 cm) Lemo JetPack Kabel zu Flugleitungen, 5v
JETPACK 5V, 2-PIN LEMO KABEL MIT FLIEGENDEN LEITUNGEN ermöglicht es dem Endverbraucher, seinen eigenen Stecker am anderen Ende für die gewünschte Spannung anzubringen
Core SWX JP-V-BASE V-Mount Jetpack
Das Jetpack von Switronix bietet alle Leistungsausgänge, die Sie jemals brauchen werden, in einem superkompakten Design.
Das JetPack V-Baseumfasst
Zwei Powertap-Ausgänge (zur Stromversorgung von Monitoren, Lampen usw.)Einen USB-Ausgang (z.B. für Redmote, Tascam DR-05, andere USB-Geräte)Ein 5-V-Lemo-Ausgang (z. B. Zoom, AJA)Ein geregelter 7,2-V-Ausgang (z. B. für HDV-Kameras, DSLRs)Ein regulierter 12-V-Ausgang (z. B. Blackmagic, 12-V-Zubehör)
Das Vollaluminium-Design reduziert das Gewicht und ist dennoch widerstandsfähig. Das JetPack verfügt über drei 1/4-20-Befestigungspunkte sowie eine optionale "Käse"-Rückplatte, die zusätzliche 1/4-20- und 3/8-16-Gewindebohrungen bietet.
Größe: 6" x 3,5" x 1,88''Gewicht: 1,2 lbsV-Mount Batterie-Eingang: DC 11-17vP-Tap(2) Ausgänge: DC 11-17v, unreguliert
Ausgänge durch JetPack-Schalter gesteuert
USB-Ausgang: 5V, 1a**LEMO 2-polig(0B): 5V, 2,5aLEMO 3-polig (0B): 7,2 V, 2,5 ALEMO 4-polig(0B): 12 V, 2,5 A
Core SWX Jetpack Befestigungspunkte
Befestigungspunkte: 1/4-20-Gewinde an der Unterseite und zwei an der RückseiteBefestigungspunkte: M3 Schraubenmuster auf der Rückseite für optionale Cheese Plate
*ACHTUNG! Optionale Käseplatte**ACHTUNG: Das JetPack lädt ein iPad auf, allerdings langsamer als das Apple-Ladegerät. Sie werden "Not Charging" auf dem iPad-Bildschirm sehen, aber das bedeutet nur, dass 2,1A Strom nicht an das Gerät geliefert wird.
Core SWX JP-V-FS7 V-Mount Jetpack für Sony PXW-FS7
V-Mount-Jetpack für Sony PXW-FS7
Das Jetpack bietet alle Leistungsausgänge, die Sie jemals brauchen werden, in einem superkompakten Design. Das JetPack Sony FS7 umfasst
Stromanschluss für Ihre Sony FS7Zwei Powertap-Ausgänge (zur Stromversorgung von Monitoren, Lampen usw.)Einen USB-Ausgang (z. B. Redmote, Tascam DR-05, andere USB-Geräte)Ein 5-V-Lemo-Ausgang (z. B. Zoom, AJA)Zwei geregelte 4-polige 12-V-Hirose-Ausgänge (z. B. für HDV-Kameras, DSLRs)Ein 4-poliger XLR-StromeingangHalterung zur Montage des Jetpacks direkt an der Rückseite der Sony FS7 als Alternative zum XDCA-FS7
Das Vollaluminium-Design reduziert das Gewicht und ist dennoch widerstandsfähig. Das Switronix JetPack verfügt über drei 1/4-20 Befestigungspunkte sowie eine optionale "Käse"-Rückplatte, die zusätzliche 1/4-20 und 3/8-16 Gewindelöcher bietet.
JP-V-FS7 Technische Daten
Abmessungen 20,32 cm x 8,89 cm x 4,77 cmGewicht 0,77 kgV-Mount Batterie/4-Pin XLR Eingang DC 11-17vFS7 Power Input Pin DC 11-17v, ungeregeltP-Tap(2) Ausgänge DC 11-17 V, ungeregeltLEMO 2-polig (0B) 5 V, 2,5 AHRS 4-polig 12v, 2,5a. Enthält zwei 12-V-AusgängeBefestigungspunkte1/4-20 Gewinde an der Unterseite und zwei an der RückseiteBefestigungspunkteM3-Schraubenmuster auf der Rückseite für optionale Cheese PlateUSB-Ausgang5V, 1a. Das JetPack lädt ein iPad auf, allerdings langsamer als das Apple-Ladegerät. Auf dem iPad-Bildschirm wird "Not Charging" angezeigt, was aber nur bedeutet, dass das Gerät nicht mit 2,1 A Strom versorgt wird.
Deity SPD-1
Das Deity SPD-1 unterstützt sowohl intelligente als auch nicht intelligente Batterien mit dreifachem DC-Eingang und Hot-Swap-Funktionalität. Das Gerät zeigt auch Batterie-Telemetriedaten an, um den Überblick über den Stromverbrauch zu behalten. Die Überwachung des Stromverbrauchs am Set ist entscheidend für eine reibungslose Produktion. Mit dem SPD-1 können Sie Ihren Stromverbrauch leicht verfolgen und sicherstellen, dass Ihnen nie zur falschen Zeit der Strom ausgeht. Dies ist besonders wichtig, wenn Sie die Produktion unterbrechen oder zwischen verschiedenen Standorten wechseln.
Das 1,1-Zoll-Farbdisplay des SPD-1 liefert Ihnen alle Informationen, die Sie benötigen, wie z. B. Gesamtstromverbrauch, Batterietemperaturen, Spannung, Batterielebensdauer und Anzahl der Batteriezyklen. Mit den verriegelnden Kippschaltern können Sie Ihre Geräte einfach ein- und ausschalten, was einen zufälligen Stromverlust verhindert.
Die SPD-1 Power Distribution Box verfügt außerdem über zwei 1/4"-Gewindeanschlüsse, mit denen Sie das Gerät in jeder beliebigen Position sicher befestigen können. Mit dem umkehrbaren Montageclip lässt sich die Ausrichtung des Geräts bei Bedarf leicht ändern, und der Betriebsbereich von 12 bis 18 V gewährleistet, dass es mit einer Vielzahl von Geräten funktioniert.
Darüber hinaus verfügt die Power Distribution Box über einen leicht zugänglichen 5V2A Typ A USB-Anschluss an der Vorderseite, über den Sie Ihre Geräte ganz einfach aufladen und mit Strom versorgen können. Und mit sechs ungeregelten 4-Pin-Push-Power-Ausgängen (die Hirose-kompatibel sind) können Sie mehrere Geräte gleichzeitig mit Strom versorgen. Die sechs Ausgänge sind auf zwei Stromkreisgruppen aufgeteilt, so dass Sie Zusatzgeräte ein- und ausschalten können, ohne Ihre Hauptgeräte abschalten zu müssen.
Deity SPD-1 Kompatibilität mit folgenden Geräten
Sound Devices MX-HIROSE DC-EingangsschlittenSoundgeräte 633, 664, 688Sound Devices A10-RX A-TA3 Adapter, A10-RX A-XLRZaxcom Nova, Nova 2Zaxcom Deva 24Zoom F8, F8n, F8n PoZoom F4Soundgeräte A10-RX A-TA3 Adapter, A10-RX A-XLRLectrosonics SREXT SR Befestigungssatz, DSR4EXT, DCR822Wisycom MCR54 EndplatteMiPro MR-90SCSony UWP-D
Im Lieferumfang enthalten
1x Deity SPD-1 Smart Power Verteiler1x SPD-T4BATT (TA4f auf NH2054 Akkuschale)1x Garantiekarte1x Deity Aufkleber1x QR-Karte für digitales Handbuch
MID49 Breakout Boxes and Side Plate BundleSKU: M49-BOB-SPB-X1
Bundle aus Breakout-Boxen und Seitenplatte für RED KOMODO-X enthält:Breakout-Seitenplatte für RED KOMODO und KOMODO-XAB-1 (RED Komodo-X, V-Raptor, ARRI Alexa Mini)EB-1 (RED Komodo, Komodo-X, V-Raptor)
MID49 Breakout Boxes and Side Plate Bundle for RED V-Raptor
SKU: M49-BOB-SPB-VR1
Bundle aus Breakout-Boxen und Seitenplatte für RED V-Raptor enthält:Breakout-Seitenplatte für RED V-Raptor - wird an der Seite des RED V-Raptor befestigt und bietet 1/4-20, 3/8-16 mit ARRI-Aufnahmebolzen, eine ARRI-Standardrosette und M4x20mm-Gewindebohrungen. Zwei versetzte 1/4-20 Löcher, die mit den RED-Abständen übereinstimmen, ermöglichen die Befestigung bestimmter Produkte von Drittanbietern wie GDU Atlas Side Handle (Raptor, rechts)AB-1 (RED V-Raptor) - Ein passiver Adapter, der den 5-poligen 00-LEMO-Anschluss der Kamera in zwei Standard-XLRs voller Größe umwandelt und mit einer unverlierbaren 1/4-20-Schraube und einem Gummipad befestigt wird.EB-1 (RED Komodo, Komodo-X, V-Raptor) - Ein EXT-Port-Konverter, der Anschlüsse nach Industriestandard bietet:Genlock: 75-Ohm-BNCTimecode: 5-polig 0BCTRL: 4-polig 00Auslöser: 3-polig FischerEXT-Durchgang: 9-polig 0B
MID49 EXT Breakout EB-1 SKU: M49-BOB-EB1
EXT Breakout EB-1 (RED Komodo, Komodo-X, V-Raptor) konvertiert den 9-poligen 0B LEMO EXT-Anschluss der Kamera in die unten aufgeführten Industriestandard-Anschlüsse:
Genlock: 75-Ohm-BNCTimecode: 5-polig 0BCTRL: 4-polig 00Auslöser: 3-polig FischerEXT-Durchgang: 9-polig 0B
Wird mit einer unverlierbaren 1/4-20 Schraube und einem Gummipuffer am Kameragehäuse oder an Seitenplatten wie der Breakout Side Plate Only (RED Komodo-X) (separat erhältlich) befestigt. Zwei M4-Gewindebohrungen im 20-mm-ARRI-Abstand stehen zur Verfügung, um die Breakout-Box-Montagehalterung (ARRI 3/8-16, Rear Mount) (separat erhältlich) hinzuzufügen, die die Befestigung des EB-1 mit einer 3/8-16-Schraube mit ARRI-Passstiften ermöglicht. 8 Zoll (20cm) Kabellänge mit rechtwinkligem LEMO-kompatiblen Stecker.
Gewicht: 70gAbmessungen (BxLxH): 54 x 271 x 19mm
Wooden Camera D-Box (2pin LEMO Kit, V-Mount)
SKU: 200100
D-Box (2 Pin LEMO Kit, V-Mount) is one of the most popular combinations of connectors including (2) 2 Pin LEMO, (2) D-Tap, (1) USB, and a male V-Mount on one side and female V-Mount on the other. Fits between any V-Mount battery plate and V-Mount battery.
Comes with
2 x 2 Pin LEMO2 x D-Tap1 x USB1 x Blank
Wooden Camera D-Box (Alexa Mini, Gold Mount)
SKU: 209100
D-Box (Alexa Mini, Gold Mount) is a custom version of popular D-Box that adds power distribution, standardized remote start/stop, and hot swap abilities for the ARRI Alexa Mini. Two 16 inch (40cm) cables exit the power plate with one going to the 8pin LEMO power plug and the other going to the 7pin EXT port.
The bottom of the D-Box has (3) 1/4-20 holes which can attach directly to Rod Clamp (15mm LW), Rod Clamp (15mm Studio), and Rod Clamp (19mm). For an adjustable mount system, use the Battery Slide paired with the same Rod Clamps listed above. Wooden Camera D-Box will attach to the ARRI BAP-1 and instructions on how to do this are included in the box.
Authentic Anton Bauer plate provides 1x D-Tap (unregulated) and is hard wired to the D-Box.
D-Box Slots Included
7 pin LEMO - EXT PortReplica of connector on rear of cameraMaintains functionality of external communication, R/S, and powerNote this slot is not swappable2 pin LEMO - 12V UnregulatedARRI standard wiringThis slot can be swapped for Hirose, 4pin LEMO, or D-Tap (note that only 1x D-Tap can occupy slot 2 or 3)2 pin LEMO - 12V UnregulatedARRI standard wiringThis slot can be swapped for Hirose, 4pin LEMO, or D-Tap (note that only 1x D-Tap can occupy slot 2 or 3)3 pin Fischer - 24V RegulatedRegulator built in to convert battery voltage to 24VMaximum 3A shared between slot 4/5Note this slot is not swappable3 pin Fischer - 24V RegulatedRegulator built in to convert battery voltage to 24VMaximum 3A shared between slot 4/5Note this slot is not swappable4 pin Mini XLR - 12V InputHot swappable power input with included 7 inch pigtail cable for standard 4 pin XLR (12V nominal)Capable of providing power to accessories and camera with out brick battery attachedNote this slot is not swappable
Specifications
Weight 534 gDimensions 90 mm x 146 mm x 43mm
Wooden Camera D-Box (Alexa Mini, V-Mount)
SKU: 209200
D-Box (Alexa Mini, V-Mount) is a custom version of the popular D-Box that adds power distribution, standardized remote start/stop, and hot swap abilities for the ARRI Alexa Mini. Two 16 inch (40cm) cables exit the power plate with one going to the 8pin LEMO power plug and the other going to the 7pin EXT port. The bottom of the D-Box has (3) 1/4-20 holes which can attach directly to our Rod Clamp (15mm LW), Rod Clamp (15mm Studio), and Rod Clamp (19mm). For an adjustable mount system, use the Battery Slide paired with the same Rod Clamps listed above.
This product Wooden Camera D-Box will attach to the ARRI BAP-1 and instructions on how to do this are included in the box.
Authentic IDX V-Mount plate provides 2x D-Tap (unregulated) and is hard wired to the D-Box. Inside the D-Box is a 10A fuse.
D-Box Slots Included
7 pin LEMO - EXT PortReplica of connector on rear of cameraMaintains functionality of external communication, R/S, and powerNote this slot is not swappable2 pin LEMO - 12V UnregulatedARRI standard wiringThis slot can be swapped for Hirose, 4pin LEMO, or D-Tap (note that only 1x D-Tap can occupy slot 2 or 3)2 pin LEMO - 12V UnregulatedARRI standard wiringThis slot can be swapped for Hirose, 4pin LEMO, or D-Tap (note that only 1x D-Tap can occupy slot 2 or 3)3 pin Fischer - 24V RegulatedRegulator built in to convert battery voltage to 24VMaximum 3A shared between slot 4/5Note this slot is not swappable3 pin Fischer - 24V RegulatedRegulator built in to convert battery voltage to 24VMaximum 3A shared between slot 4/5Note this slot is not swappable4 pin Mini XLR - 12V InputHot swappable power input with included 7 inch pigtail cable for standard 4 pin XLR (12V nominal)Capable of providing power to accessories and camera with out brick battery attachedNote this slot is not swappable
Specifications
Weight 534 gDimensions 90 mm x 146 mm x 43mm
Wooden Camera D-Box (RED DSMC2, Gold Mount)
SKU: 234000
Wooden Camera D-Box (Weapon/Epic-W/Scarlet-W/Raven, Gold Mount) is a custom version of our popular D-Box that adds power distribution, standardized remote start/stop, and hot swap abilities for the RED DSMC2 cameras. The D-Box is completely tool-less for installation and utilizes our Cable-less interface which attaches directly to the back of the camera body, Base Expander Module, REDVolt Expander Module, and the OffHollywood O-Mods.
Connectors on the D-Box (Weapon/Epic-W/Scarlet-W/Raven, Gold Mount) are contoured to match the Expander Modules' which allow for all cables to be installed with no collisions. The module communicates with the camera and allows any ARRI standard start/stop trigger to be used with the 3pin Fischer port. The DC input on the D-Box is the same as the camera's LEMO allowing for an AC power supply or external power plate to be connected to power accessories and camera during a battery change. When both battery and DC input are utilized, the Wooden Camera D-Box defaults to the DC input, leaving the battery fully charged.
Overview
Authentic Anton Bauer Gold Mount plate provides 2x D-Tap (unregulated) on the power plate itself but we should note that one D-Tap is obscured by the right side power outputs. Inside the D-Box is a 10A fuse and replacement fuses are included.
Specifications
Weight: 610g Dimensions: 228.6 mm x 177.8 mm x 127 mm
D-Box Connections
1. D-Tap - 12V Unregulated- This slot can be swapped for Hirose, 2pin LEMO, or 4pin LEMO2. D-Tap - 12V Unregulated- This slot can be swapped for Hirose, 2pin LEMO, or 4pin LEMO3. 2 pin LEMO - 12V Unregulated- ARRI standard wiring4. 2 pin LEMO - 12V Unregulated- ARRI standard wiring5. 3 pin Fischer - 24V Regulated- Regulator built in to convert battery voltage to 24V- Maximum 3A shared between the two 3pin Fischers- ARRI standard start/stop capabilities6. 3 pin Fischer - 24V Regulated- Regulator built in to convert battery voltage to 24V- Maximum 3A shared between the two 3pin Fischers- ARRI standard start/stop capabilities7. USB - 5v Regulated- Provides 2A for iPhone/iPad charging8. DC Input - 12-16V- DC input on the D-Box is the same as the camera's LEMO- Priority is given to DC Input to preserve battery charge when both sources connected
Wooden Camera D-Box (RED DSMC2, Power Distribution Portion Only)
SKU: 235000
Wooden Camera D-Box (Weapon, Power Distribution Portion Only) is for owners of Cable-less V-Mount, Blueshape, of Gold Mount that want to add power distribution, standardized remote start/stop, and hot swap abilities to their RED DSMC2 camera. The completed Wooden Camera D-Box assembly is tool-less for installation and utilizes our Cable-less interface which attaches directly to the back of the camera body, Base Expander Module, REDVolt Expander Module, and the OffHollywood O-Mods.
Connectors on the D-Box are contoured to match the Expander Modules' which allow for all cables to be installed with no collisions. The module communicates with the camera and allows any ARRI standard start/stop trigger to be used with the 3pin Fischer port. The DC input on the D-Box is the same as the camera's LEMO allowing for an AC power supply or external power plate to be connected to power accessories and camera during a battery change. When both battery and DC input are utilized, the D-Box defaults to the DC input, leaving the battery fully charged.
Overview
When combined with V-Mount or Gold Mount plate, one D-Tap is obscured by the right side power outputs. Inside the D-Box is a 10A fuse and replacement fuses are included.
Specifications
Weight: 362.8 gDimensions: 228.6 x 177.8 x 127 mm
D-Box Connections
1. D-Tap - 12V Unregulated- This slot can be swapped for Hirose, 2pin LEMO, or 4pin LEMO2. D-Tap - 12V Unregulated- This slot can be swapped for Hirose, 2pin LEMO, or 4pin LEMO3. 2 pin LEMO - 12V Unregulated- ARRI standard wiring4. 2 pin LEMO - 12V Unregulated- ARRI standard wiring5. 3 pin Fischer - 24V Regulated- Regulator built in to convert battery voltage to 24V- Maximum 3A shared between the two 3pin Fischers- ARRI standard start/stop capabilities6. 3 pin Fischer - 24V Regulated- Regulator built in to convert battery voltage to 24V- Maximum 3A shared between the two 3pin Fischers- ARRI standard start/stop capabilities7. USB - 5v Regulated- Provides 2A for iPhone/iPad charging8. DC Input - 12-16V- DC input on the D-Box is the same as the camera's LEMO- Priority is given to DC Input to preserve battery charge when both sources connected
Wooden Camera D-Box (RED DSMC2, V-Mount)
SKU: 233900
Wooden Camera D-Box (Weapon/Epic-W/Scarlet-W/Raven, V-Mount) is a custom version of our popular D-Box that adds power distribution, standardized remote start/stop, and hot swap abilities for the RED DSMC2 cameras. The D-Box is completely tool-less for installation and utilizes our Cable-less interface which attaches directly to the back of the camera body, Base Expander Module, REDVolt Expander Module, and the OffHollywood O-Mods.
Connectors on the -Box (Weapon/Epic-W/Scarlet-W/Raven, V-Mount) are contoured to match the Expander Modules' which allow for all cables to be installed with no collisions. The module communicates with the camera and allows any ARRI standard start/stop trigger to be used with the 3pin Fischer port. The DC input on the D-Box is the same as the camera's LEMO allowing for an AC power supply or external power plate to be connected to power accessories and camera during a battery change. When both battery and DC input are utilized, the D-Box defaults to the DC input, leaving the battery fully charged.
Overview
Authentic IDX V-Mount plate provides 2x D-Tap (unregulated) on the power plate itself but we should note that one D-Tap is obscured by the right side power outputs. Inside the D-Box is a 10A fuse and replacement fuses are included.
Specifications
Weight: 610gDimensions: 228.6 mm x 177.8 mm x 127 mm
D-Box Connections
1. D-Tap - 12V Unregulated- This slot can be swapped for Hirose, 2pin LEMO, or 4pin LEMO2. D-Tap - 12V Unregulated- This slot can be swapped for Hirose, 2pin LEMO, or 4pin LEMO3. 2 pin LEMO - 12V Unregulated- ARRI standard wiring4. 2 pin LEMO - 12V Unregulated- ARRI standard wiring5. 3 pin Fischer - 24V Regulated- Regulator built in to convert battery voltage to 24V- Maximum 3A shared between the two 3pin Fischers- ARRI standard start/stop capabilities6. 3 pin Fischer - 24V Regulated- Regulator built in to convert battery voltage to 24V- Maximum 3A shared between the two 3pin Fischers- ARRI standard start/stop capabilities7. USB - 5v Regulated- Provides 2A for iPhone/iPad charging8. DC Input - 12-16V- DC input on the D-Box is the same as the camera's LEMO- Priority is given to DC Input to preserve battery charge when both sources connected
Wooden Camera D-Box (RED KOMODO-X)
Erweitern Sie Ihre Stromversorgungsoptionen für die KOMODO-X, indem Sie die D-Box zu Ihrem System hinzufügen. Diese D-Box lässt sich vom nativen V-Mount der Kamera in den Gold-Mount umwandeln.
Die D-Box bietet Hot-Swap-Fähigkeiten, wenn die Stromversorgung an den DC-Eingang und eine On-Board-Batterie angeschlossen ist. Es gibt zusätzliche 12 V 2-polige, einen D-Tap-Anschluss und eine 3-polige 24 V-Stromversorgungsoption. Bei Anschluss an den EXT-Port der Kamera ist Run/Stop sowohl für die D-Box als auch für die B-Box (KOMODO, KOMODO-X, V-RAPTOR) aktiviert. Auf der Assistentenseite der Kamera befindet sich ein DC-In-Anschluss für den Anschluss zusätzlicher Stromquellen wie Blockbatterien, und eine EXT-Out-Option ist ebenfalls vorhanden, um Anschlussmöglichkeiten an eine B-Box weiterzugeben, die bei Bedarf an das System angeschlossen wird.Enthaltene Artikel: EXT-Kabel (9-poliger 0B RA-Stecker auf 9-poligen 0B RA-Stecker, 5 Zoll)SpezifikationenD-Box Goldmount (RED KOMODO-X): 259 g | 38,9 x 78,25 x 105 mmD-Box V-Halterung (RED KOMODO-X): 273,5 g | 48 x 103 x 100 mm
Wooden Camera D-Box (Sony BURANO)
Erweitern Sie Ihr Kamerasystem um zusätzliche Stromversorgungsoptionen für die Sony BURANO, indem Sie die D-Box an Ihr Kamerasystem anschließen. Die D-Box bietet zusätzliche 2-polige 12-V-Anschlüsse, einen D-Tap-Anschluss und 3-polige 24-V-Stromversorgungsoptionen. Die D-Box bietet Hot-Swap-Fähigkeiten, wenn der Strom an den DC-Eingang und einen On-Board-Akku angeschlossen ist. Wählen Sie zwischen einer Gold-Mount- oder V-Mount-Option.D-Box V-Mount (Sony BURANO): Gewicht: 400,5 g | Abmessungen: 96 x 47 x 135 mmD-Box Gold Mount (Sony BURANO): Gewicht: 394,6 g | Abmessungen: 100 x 38 x 136 mm
Wooden Camera D-Box (Sony Rialto 2)
D-Box for Sony Rialto Power Strip provides 2x two-pin LEMOs at 12V, two three-pin Fischers at 24V with R/S, and one D-Tap at 12V. Five self-securing closure cable ties attach the included Y cable to the Rialto Head cable, and a new offset bracket allows you to seamlessly mount this indispensable distro module on the Rialto 2’s new extruded form factor.
A00326 | D-Box Sony Rialto 2 Power Strip with Y Cable (110 inch/279 cm) Weight: 278 gDimensions: 46.5 mm x 170 mm x 180 mm
A00324 | D-Box Sony Rialto 2 Power Strip with Y Cable (220 inch/559 cm) Weight: 378 gDimensions: 200 mm x 200 mm x 30 mm
Included Items
D-Box Sony Rialto Power StripD-Box Extension Bracket (Sony Rialto 2)D-Box Power Strip Replacement Y Cable (110 inch/279 cm) / (220 inch/559 cm)
Wooden Camera D-Box (Sony Venice, Venice 2, V-Mount)
D-Box (Sony Venice, Venice 2, V-Mount) is a custom version of our popular D-Box™ that adds power distribution, standardized remote start/stop, and hot swap abilities for the Sony Venice, Sony Venice 2 camera. The D-Box™ main unit attaches to the back of the AXS-R7 or to the V-Mount plate on the camera rear and the Power Strip portion attaches to the top right side of the camera via a 3pin Fischer and the tape hook threaded hole.
Connectors on the D-Box™ Power Strip are contoured to match the camera profile and connector angle which allows for all cables to be installed with no collisions. The module communicates with the camera and allows any ARRI standard start/stop trigger to be used with the 3pin Fischer port including the ARRI UMC-4 / WCU-4. The DC input on the D-Box™ is the same as the camera's 4pin XLR connector allowing for an AC power supply, external power plate, or VCLX block battery to be connected to power accessories and camera during a battery change. When both battery and DC input are utilized, the D-Box™ defaults to the DC input, leaving the onboard battery fully charged.
Physical fuses have been replaced by a processor controlled amp limit which is settable to 3.8, 5.8, or 9 amps using the slide switch on the operator's side. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again.
The "DC IN" and "BATT" LEDs are dual LEDs. This means the LED If battery voltage is above 12.5V the LED will be green. If the battery voltage is below 12V the LED will be red. If the battery voltage is between those values the LED will be orange (red + green). Flashing may occur during phase transition.
Highest quality Anton Bauer components are used in the V-Mount assembly and the unibody power plate design is both extremely durable and lightweight.
Interfaces
1x V-Mount Power Plate2x 3pin Fischer at 24V with Run Stop- Regulator built in to convert battery voltage to 24V- Maximum 3A surge, 2.5A sustained shared between connectors2x 2pin at 12V unregulated- ARRI standard wiring- Maximum 7A current rating, shared between connectors2x D-Tap at 12V unregulated- Maximum 9A current rating, shared between connectors1x 5V USB - Maximum 2.5A1x 4pin XLR DC Input- For use with 14.4V block batteries- DC Input takes priority when voltage is between 12.9–18V- Accessories are powered when utilizing DC Input
Specifications
Weight: 484gDimensions: 31.8 mm x 114.3 mm x 133.35 mm
1.850,00 €*
Brutto: 2.201,50 €
Zahlen Sie mit:
Wir versenden mit:
Schneller Versand
Persönliche Beratung und Showroom vor Ort
Bequemer Kauf auf Rechnung
Hotline 0211 930 730-33
Funktionale Cookies sind für die Funktionalität des Webshops unbedingt erforderlich. Diese Cookies ordnen Ihrem Browser eine eindeutige zufällige ID zu damit Ihr ungehindertes Einkaufserlebnis über mehrere Seitenaufrufe hinweg gewährleistet werden kann.
Maschinenkennung:
Sicherheitstoken zur identifizierung der maschine.
Stripe orig props:
Stripe-referrer-informationen.
Private maschinenkennung:
Sicherheitstoken zum identifizieren des privaten computers.
Private maschinenkennung:
Sicherheitstoken zum identifizieren des privaten computers.
Stripe orig props:
Stripe-referrer-informationen.
Private maschinenkennung:
Sicherheitstoken zum identifizieren des privaten computers.
Site-auth:
Stripe-authentifizierungscookie.
Stripe csrf:
CSRF-token.
stripe-payments.stripe_pm.name:
stripe-payments.stripe_pm.description
Private maschinenkennung:
Sicherheitstoken zum identifizieren des privaten computers.
Site-auth:
Stripe-authentifizierungscookie.
Stripe csrf:
CSRF-token.
Site-auth:
Stripe-authentifizierungscookie.
Stripe csrf:
CSRF-token.
stripe-payments.stripe_pm.name:
stripe-payments.stripe_pm.description
Site-auth:
Stripe-authentifizierungscookie.
Stripe csrf:
CSRF-token.
stripe-payments.stripe_pm.name:
stripe-payments.stripe_pm.description
Amazon Pay
CSRF-Token:
Das CSRF-Token Cookie trägt zu Ihrer Sicherheit bei. Es verstärkt die Absicherung bei Formularen gegen unerwünschte Hackangriffe.
PayPal-Zahlungen
CAPTCHA-Integration
Zeitzone:
Das Cookie wird verwendet um dem System die aktuelle Zeitzone des Benutzers zur Verfügung zu stellen.
Herkunftsinformationen:
Das Cookie speichert die Herkunftsseite und die zuerst besuchte Seite des Benutzers für eine weitere Verwendung.
Session:
Das Session Cookie speichert Ihre Einkaufsdaten über mehrere Seitenaufrufe hinweg und ist somit unerlässlich für Ihr persönliches Einkaufserlebnis.
Cookie Einstellungen:
Das Cookie wird verwendet um die Cookie Einstellungen des Seitenbenutzers über mehrere Browsersitzungen zu speichern.
Amazon Pay:
Das Cookie wird für Zahlungsabwicklungen über Amazon eingesetzt.
Aktivierte Cookies:
Speichert welche Cookies bereits vom Benutzer zum ersten Mal akzeptiert wurden.
Cache Behandlung:
Das Cookie wird eingesetzt um den Cache für unterschiedliche Szenarien und Seitenbenutzer zu differenzieren.
Sendinblue:
Sendinblue tracker
Erlaubt es Google, personenbezogene Daten für Online-Werbung und Marketing zu sammeln.
Google Werbung und Marketing
Google Werbung und Marketing
Google Werbung und Marketing
Service Cookies werden genutzt um dem Nutzer zusätzliche Angebote (z.B. Live Chats) auf der Webseite zur Verfügung zu stellen. Informationen, die über diese Service Cookies gewonnen werden, können möglicherweise auch zur Seitenanalyse weiterverarbeitet werden.
Doofinder:
Das Cookie wird verwendet um Benutzerinteraktionen mit der Seitensuche zu verfolgen. Die Daten können für Optimierungen der Suchfunktion genutzt werden.
YouTube-Video
YouTube-Video
YouTube-Video
Merkzettel
Local Storage:
Speichert einen Zeitstempel um Elemente auf Wunsch für eine gewisse Zeit ausblenden zu können.
Tracking Cookies helfen dem Shopbetreiber Informationen über das Verhalten von Nutzern auf ihrer Webseite zu sammeln und auszuwerten.
Google Analytics:
Google Analytics wird zur der Datenverkehranalyse der Webseite eingesetzt. Dabei können Statistiken über Webseitenaktivitäten erstellt und ausgelesen werden.
Google Analytics:
Cookie von Google für Website-Analysen. Erzeugt statistische Daten darüber, wie der Besucher die Website nutzt.
Marketing-Cookies werden von Drittanbietern oder Verlegern verwendet, um personalisierte Werbung anzuzeigen. Sie tun dies, indem sie die Besucher auf den Webseiten verfolgen.
Google Ads:
Dieses Cookie wird gesetzt, wenn ein User über einen Klick auf eine Google Werbeanzeige auf die Website gelangt. Es enthält Informationen darüber, welche Werbeanzeige geklickt wurde, sodass erzielte Erfolge wie z.B. Bestellungen oder Kontaktanfragen der Anzeige zugewiesen werden können.
Google Ads:
Werbung Targeting
Google AdSense:
Das Cookie wird von Google AdSense für Förderung der Werbungseffizienz auf der Webseite verwendet.
Bing Ads:
Das Bing Ads Tracking Cookie wird verwendet um Informationen über die Aktivität von Besuchern auf der Website zu erstellen und für Werbeanzeigen zu nutzen.
Für Statistiken und Shop-Performance-Metriken genutzte Cookies.
Google Tag Manager:
Cookie von Google zur Steuerung der erweiterten Script- und Ereignisbehandlung.
Wir respektieren Ihre Privatsphäre
Diese Website verwendet Cookies, um Ihnen die bestmögliche Funktionalität bieten zu können... Mehr Informationen.