Core SWX RM-GPTS-DSMC2 The Core SWX RM-GPTS-DSMC2 is a 15mm rod mount bracket with dual v-mount battery plates allow for continuous battery operation and hot swapping packs on the fly. By having two v-mount battery packs mounted you can easily remove the depleted battery while the leaving the other battery connected so that there is no down time. The bracket is compatible with all v-mount battery packs to provide a secure mounting surface for your rig setup. The system is terminated with a 18″ 6-pin RED LEMO to power your RED DSMC2 as well as one ptap output for powering accessories. The cheese plate features many 1/4-20 thread mounting points for attaching devices, arms, etc. Rods NOT included Features 15mm rail mount cheese plate with a sharkfin v-mount battery plate and 18″ 6-pin RED LEMO for RED DSMC2Features a dual v-mount battery plate which allows for continuous battery operation and hot swapping packs on the flyCompatible with all v-mount battery packs to provide a secure mounting surface for your rig setupFeatures a 18″ 6-pin RED LEMO to power your RED DSMC2 as well as one ptap output for powering accessoriesThe cheese plate features many 1/4-20 thread mounting points for attaching devices, arms, etc
Core SWX RMV-BMPC4 SKU: RMV-BMPC4 The Core SWX RMV-BMPC4 is a 15mm rod mount bracket with v-mount battery plate. The bracket works with all v-mount battery packs to provide a secure mounting surface for your rig setup. The Cheese Plate can be configured to mount vertically or horizontally, based on balance preference. The system is terminated with a 10″ 2-pin coil cable to power your Blackmagic Design Pocket 4K or 6K as well as one p-tap output for powering accessories. The cheese plate is configured with many 1/4-20 thread mounts for attaches devices, arms, etc., along with a soft Velcro rear backing to quickly attach a wireless audio RX, a wireless video RX, etc. without the need for additional hardware. Features 15mm rail mount cheese plate with v-mount battery plate and 10" 2-pin coiled cable for BMD Pocket 4K/6KWorks with all v-mount battery packs to provide a secure mounting surface for your rig setupThe Cheese Plate can be configured to mount vertically or horizontallyFeatures a 10″ 2-pin coil cable to power your Blackmagic Design Pocket 4K or 6K as well as one p-tap output for powering accessoriesThe cheese plate is configured with many 1/4-20 thread mounts for attaches devices, arms, etcSoft Velcro rear backing to quickly attach a wireless audio RX or a wireless video RX Rods NOT included
Core SWX RMV-KOM2 The Core SWX RMV-KOM2 is a 15mm rod mount bracket with v-mount battery plate. The bracket works with all v-mount battery packs to provide a secure mounting surface for your rig setup. The Cheese Plate can be configured to mount vertically or horizontally, based on balance preference. The system is terminated with a 10″ 2-pin coil cable to power your RED Komodo as well as one p-tap output for powering accessories. The cheese plate is configured with many 1/4-20 thread mounts for attaches devices, arms, etc., along with a soft Velcro rear backing to quickly attach a wireless audio RX, a wireless video RX, etc. without the need for additional hardware. Features 15mm rail mount cheese plate with a V-mount battery plate and 10″ 2-Pin coil cable for RED KomodoWorks with all v-mount battery packs to provide a secure mounting surface for your rig setupThe Cheese Plate can be configured to mount vertically or horizontallyFeatures a 10″ 2-pin coil cable to power your RED Komodo as well as one p-tap output for powering accessoriesThe cheese plate is configured with many 1/4-20 thread mounts for attaches devices, arms, etc.Soft Velcro rear backing to quickly attach a wireless audio RX or a wireless video RX
Core SWX V-Mount Conversion Plate A-GP-S SKU: AGPS The Core SWX A-GP-S is a temporary solution to allow the use of V-Type batteries on 3-stud configured cameras. It can also be used as a charge adapter, enabling you to temporarily charge V-Type batteries on PRO-X series 3-Stud charging equipment. Core SWX A-GP-S Technical data Input DC 11-17vOutput for Camera DC 11-17v, UnregulatedOutput for P-Tap DC 11-17v, UnregulatedSize 8.26 cm x 13.97 cm x 3.81 cmWeight 0.32 kg
HedBox HBP-NPF HedBox HBP-NPF allows you to power any V-Mount/V-Lock Professional Broadcast Camcorder, with standard two High Capacity L-series or NP-F Batteries, as long as the voltage is equivalent to 7.2V ~ 7.4V. The combined voltage of the two L-series or NP-F Batteries will be 14.4V ~ 14.8V, which is the standard output power of a V-Mount Battery Pack, that use all world brand Professional Broadcast Camcorders… HBP-NPF allows you to power any V-Mount/V-Lock Professional Broadcast Camcorder, with standard two High Capacity L-series or NP-F Batteries, as long as the voltage is equivalent to 7.2V ~ 7.4V. The combined voltage of the two L-series or NP-F Batteries will be 14.4V ~ 14.8V, which is the standard output power of a V-Mount Battery Pack, that use all world brand Professional Broadcast Camcorders… V-Mount Connection Holder HBP-NPF is equip with standard V-mount connection, and we adopt the high quality lightweight aluminium V-wedge that ensures the reliable and safe mounting. Built-in D-tap Output 14.8V 72W, 6A DC Socket A D-Tap DC output socket is equipped on the side of the HBP-NPF plate. With this external Power supply facility, you can connect on-camera LED light, Video Monitor or Wireless Transmitter on the D-tap socket, and get power simultaneously together with Battery Plate attached to the Camera, or totally separately like independent Power Station. The Max power from D-tap is 72W, 6A. 4-LED Power Monitor Indicator HBP-NPF V-Lock Battery Converter Plate have build in 4-LED Power Monitor indicator that, upon the press of test button, shows whether 100%, 75%, 50%, or 25% of power is left remaining in the mounted DV Battery Packs. Technical data Model: HBP-NPF V-lock DV NP-F Battery Converter Power Adapter PlateMount Type: V-Lock ( High Quality Aluminium Alloy wedge plate)DV Battery Slots: 2 x Sony NP-F Style BatteryOutput Voltage: DC 13 – 16.8V , 8A / 72W (max)Support Bat Voltage: DC 7.2 – 7.6VSupported Capacity: From 1400mAh to 20000mAhD-Tap DC Output: 14.8V / 8A / 72W (max)Power Meter: Blue Color 4-LED Power Monitor ( Display 100%, 75%, 50%, or 25% bat. capacity )Operating Temperature: –20°C to +45°CDimensions (WxDxH): 96 x 22 x 151 mmWeight: 140 gOperational Method: Mount 2 x DV Sony NPF Style battery to generate 14.8V / 8A V-lock mount DC Power
IDX P-V2 The IDX P-V2 is a rugged V-Plate to convert cameras without a rear V-Mount battery connection, so that any of the V-Mount ENDURA batteries can be easily attached. The P-V2 is designed with multiple mounting holes to fit virtually all professional video cameras, with the added advantage of a built-in 2-pin D-Tap 50W DC output. The P-V2 can also be used as the V-Mount adaptor for many types of monitors, displays, test instruments and more.
Shape 2 V-MOUNT AND 2 CABLES FOR ATOMOS SUMO BATTERY PLATE SKU: 2VMAB Shape 2 V-MOUNT AND 2 CABLES FOR ATOMOS SUMO BATTERY PLATE includes 2 x Shape SH1VMAB
Shape Sony FX6 V-Mount pivoting battery plate SKU: VBFX6 The SHAPE V-Mount pivoting battery plate for Sony FX6 attaches to the rear of the top plate (FX6TP) and supports a V-mount battery while leaving access to the camera’s standard battery compartment. Our V-mount battery plate provides the right battery voltage and amperage to use with your Sony FX6 camera. By pivoting the battery plate, you have access to the BPU battery of the camera. A swivel system let you pivot the battery plate up and down. It features 1 D-Tap port for powering accessories. It also uses a digital fuse that monitors the D-Tap ports and disables them if they exceed the set current for accessories while leaving the camera running. It connects to the camera using the SHAPE 19.5V output D-Tap power cable for Sony FX6. The cable regulates the voltage from a D-Tap source to the proper 19.5 V required to power an FX6 camera. This allows you to power your camera using any V-mount battery with a D-Tap plug. The cable has a total end-to-end length of 15″ (38 cm). A universal cheeseplate with 1/4″-20 and 3/8”-16 threaded holes. The cheeseplate can tilt up and down with a patented 15 mm Push-button system to provide easy access to the rear connector and have access to the BPU battery. Features V-Mount pivoting battery plate compatible with Sony FX6 top plate (FX6TP) only Push-button system lets you tilt the battery plate up and down Easy access to the rear connector (Please refer to the camera’s operating manual for proper usage) Attaches to the Rear of the Sony FX6 top plate (FX6TP) Supports V-Mount Battery (1) D-Tap Ports & Protective Digital Fuse (1) D-Tap Power Cable for Sony FX6 provide 19.5V power output Multiple holes on top and side of the cheeseplate Made of CNC Aluminum
TILTA Battery Plate for RED V-RAPTOR / KOMODO-X This Battery Plate adapts the RED V-RAPTOR’s Micro V-Mount Battery Plate to either a Gold Mount or Full Sized V-Mount Battery Plate as well as provides a convenient slot to power and mount the Advanced I/O Module (not included). The V-Mount option features an adjustable plate that allows you to fine tune the height of your battery in relation to the camera body. This allows you to better accommodate different sized batteries and helps keep your build balanced and clean. When using our Top Plate, you can install the Battery Plate Security Attachment for an additional point of contact between your Battery Plate and Camera Cage. This Battery Plate includes the following power outputs: 2 x 14.8V 2-Pin LEMO Port1 x 14.8V P-Tap Port1 x USB-C Port
TILTA Battery Plate for Sony BURANO This Battery Plate adapts the Sony Burano’s integrated V-Mount Battery Plate to either a Gold Mount or V-Mount Battery Plate with additional power outputs. This expands users’ options for distributing power as well as provides a convenient power input that accommodates DC power for hot swapping. This Battery Plate includes the following power outputs: 1 x 6-Pin LEMO DC Input (12V-28V)1 x P-Tap Port (14.8V 3.8A)1 x USB-C Port ( PD3.1 65W )1 x 3-Pin Fischer Lemo (24V 3 A)1 x 3-Pin Fischer Lemo (14.8V 3.8 A)1 x 2-Pin Lemo (14.8V 3 A) Features POWER OUTPUTS Includes P-Tap, 3-Pin Fischer, 2-Pin Fischer and USB-CDC POWER INPUT via 6-Pin Lemo Provides Options for Extended Power and Hot SwappingBATTERY OPTIONS for Either V-Mount or Gold Mount BatteriesEXTENSION Positions Batteries Further from the Camera Body which Supports Larger BatteriesLIGHTWEIGHT & DURABLE Aluminum Alloy Construction
Battery Slide Pro (Canon C300mkIII, C400, C500mkII) Battery Slide Pro (Canon C300mkIII, C400, C500mkII) utilizes a WC Pro Gold Mount or V-Mount plate and provides battery voltage to the camera through a 4pin XLR connector. Features a custom Battery Slide which attaches directly to the back of the camera without rods. This system retains access to the battery compartment and allows an internal BPU battery to be installed, giving the user the ability to hot swap batteries. To adjust battery plate position, loosen the thumbscrew and slide. DC Input on camera-right side can be used for hot-swapping between block battery and on-board battery.Features 3x D-Tap ports at battery voltage for accessory power and digital fuse which cuts off accessory outputs while leaving the camera powered.SpecificationsWeight: 349.27 gDimensions: 152.4 x 101.6 x 44.4 mm
Wooden Camera Battery Slide Pro (Canon EOS C70/C80)Custom WC Gold Mount or V-Mount Pro battery plate for providing external power to the Canon EOS C70 and Canon EOS C80 cameras. Features 3x D-Tap ports for accessory power, including a digital fuse which cuts off accessory outputs while leaving the camera powered.Battery Slide Pro (Canon EOS C70/ C80) can be attached to any standard Canon Accessory Mount by aligning the interlocking ridges and turning the attachment thumbwheel to tighten a 1/4”-20 screw; rods are not required. This system retains access to the original C70 battery compartment, enabling operators to hot-swap power between both BPU and brick batteries. To adjust the battery plate’s vertical position, loosen the pivoting clamp and slide the plate up or down.Compatible withCanon EOS C70Canon EOS C80Wooden Camera Top Plate (Canon C70)Wooden Camera Mini Top Handle (Canon C70)Top Plate for Canon EOS C80ARCA Riser Plate for Canon EOS C80and more
Wooden Camera Battery Slide Pro V-Mount (RED KOMODO) SKU: 280300 Battery Slide Pro V-Mount ttaches to the camera-left, BP-9 battery slot and powers the camera using a right angle LEMO compatible connector. Thumbscrew can be loosened to tilt and slide the plate as needed. Three D-Taps on the plate provide battery voltage for accessories and power is monitored for over-current. If more than 5.8A are used by accessories, a digital fuse will trip and the red LED will illuminate but the camera will remain powered. Reset button can be pressed once to restart accessory power. DC Input on camera-right side can be used for hot-swapping between block battery and on-board battery. While the AC adapter that comes with the KOMODO can be used, please note that it may not be powerful enough to sustain the camera and accessory draw. If hot-swapping between Gold Mount battery and BP-955 battery is desired, please consider Battery Slide Extension for Canon BP-955 Hot Swap (RED KOMODO) which moves the battery plate further back from the camera body. Weight: 264 gDimensions: 127 mm x 114.3 mm x 44.45 mm
Wooden Camera Battery Slide Pro V-Mount (Sony FX6)SKU: 283000Battery Slide Pro V-Mount (Sony FX6) utilizes a WC Pro V-Mount plate which converts battery voltage to 19.5V for the camera, FX6 barrel connector, and a custom Battery Slide which attaches directly to the back of the camera without rods. This system retains access to the battery compartment and allows the Sony BPU series battery to be installed, giving the user the ability to hot swap V-Mount batteries. To adjust battery plate position, loosen the thumbscrew and slide. Fits rear profile of the Sony FX6 for compact packing in camera case.Features 3x D-Tap ports at battery voltage for accessory power and digital fuse which cuts off accessory outputs while leaving the camera powered
Wooden Camera Battery Slide Pro V-Mount (Sony FX9) SKU: 275900 Battery Slide Pro V-Mount (Sony FX9) utilizes a WC Pro V-Mount plate which converts battery voltage to 19.5V for the camera, FX9 barrel connector, and a custom Battery Slide which attaches directly to the back of the Sony FX9 camera without rods. This system retains access to the battery compartment and allows an internal BPU battery to be installed, giving the user the ability to hot swap V-Mount batteries. To adjust battery plate position, loosen the thumbscrew and slide. Perfectly fits rear profile of the Sony FX9 for compact packing in camera case.Features 3x D-Tap ports at battery voltage for accessory power and digital fuse which cuts off accessory outputs while leaving the camera poweredWeight: 349.27 g Dimensions: 76.2 mm x 44.45 mm x 177.8 mm
Wooden Camera Cable-less V-Mount (Weapon/Epic-W/Scarlet-W/Raven) SKU: 220600 Wooden Camera Cable-less V-Mount for the RED Weapon, Epic Weapon (Epic-W), Scarlet Weapon (Scarlet-W), and Raven cameras which utilizes an IDX brand plate with two D-Taps and the Wooden Camera pogo interface module. The assembly will attach without tools directly to the back of the RED Weapon / RED Scarlet-W / RED Epic-W / RED Raven camera, Base Expander Module, REDVolt Expander Module, and some third party modules like OMODs. This system can be converted between high and low modes. High mode is where the battery plate sits above the back of the camera. Low mode is where the plate is configured to be flush with the top of the camera body leaving batteries in a very compact configuration. An important note is that the RED DSMC2 top handle will clear RED Brick batteries when our Cable-less V-Mount plate is configured in low mode. The Cable-less V-Mount will communicate percentage or voltage data to the camera's LCD display. Intelligent batteries like RED Bricks, Blueshape, Switronix, PAG, and other batteries utilizing SMBUS or reversed SMBUS will allow for the module to communicate percentage data and estimated run time. Non-SMBUS batteries like some IDX and other low cost batteries will only provide voltage data to the camera through our module. 2x D-Tap ports for accessory power Weight: 453.592 gDimensions: 142mm x 85mm x 33mm
Wooden Camera Cradle for Bolt LT TX Cradle for Bolt LT TX allows you to mount the Teradek transmitter in-line with Gold or V-Mount camera-back power. Seamlessly integrate your Teradek Bolt 4K LT Transmitter into your camera build with the Cradle for Bolt LT TX. Choose from a selection of Gold Mount, V-Mount, or V-Mount to Gold Mount. V-Mount to Gold Mount adapts a camera-side V-Mount to a Gold Mount on-board battery. Rear (battery-side) battery plate features 3x D-Taps for accessory power at battery voltage (12-16V) and a digital fuse with reset button. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. The Teradek Bolt LT TX mounts into the cradle via one captive 1/4-20 at the bottom of the unit. The bottom of the unit features two openings - one for USB access and the other for airflow ventilation.
Wooden Camera Micro Battery Plate Adapter V-Mount to V-Mount (RED V-Raptor, KOMODO-X) SKU: A00029Micro Battery Plate Adapter V-Mount to V-Mount (RED V-Raptor) allows users to attach full-sized V-Mount batteries to their RED V-RAPTOR and RED KOMODO-X systems. It is made from anodized aluminum which ensures both durability and secure battery mounting.This power plate features 2x D-Taps for accessory power at battery voltage (11-17V) - supported by a resettable 3.8A digital E-Fuse. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. It is compatible with both micro and full-sized cinema batteries.SpecificationsWeight: 271gDimensions: 75 x 39 x 108 mm
Wooden Camera Micro Battery Plate Battery Slide Wooden Camera Micro Battery Plate Battery Slide is a Gold or V-Mount Universal Micro Battery Plate slide with two D-taps, a dual rod clamp, and a resettable 9-amp fuse. A00347 | Accessory System for Sony FX3/FX30 (V-Mount)Weight: 282.9 g Dimensions: 50 mm x 130 mm x 102 mm A00346 | Accessory System for Sony FX3/FX30 (Gold Mount)Weight: 261.6 g Dimensions: 50 mm x 130 mm x 108 mm
Wooden Camera Micro Battery Slide Pro Micro Battery Slide Pro (Blackmagic Pocket Cinema Camera 4K / 6K / 6K G2 / 6K Pro, V-Mount) utilizes an Anton/Bauer micro battery plate which provides unregulated 14v to a 2-Pin connector for camera power. The 2-Pin connector is compatible with both Blackmagic Pocket Cinema Camera 6K Pro and Blackmagic Pocket Cinema Camera 4K / 6K / 6K G2 cameras.The plate attaches via two 15mm rods and position can be adjusted along the battery slide. The user retains the ability to hot swap between the onboard Sony NPF-Series and external cinema battery. The Micro Battery Slide Pro is compatible with both micro and full-sized cinema batteries. It also features 2x D-Tap (5.8 Amps) port for accessory power as well as a digital fuse which cuts off accessory outputs, should the user exceed the set current for accessories, while leaving the camera powered.Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. Weight: 315 gDimensions: 145 x 115 x 40 mm
Universal Micro Battery Plate Universal Micro Battery Plate is made from anodized aluminum which ensures both durability and secure battery mounting. A symmetrical M3 60mm x 60mm square bolt pattern is utilized for easy universal mounting. This power plate features 2x D-Taps for accessory power at battery voltage (11-17V) - supported by a resettable 9A digital E-Fuse - rear cover plate, and captive mounting screws. Should the user exceed the set current for accessories, accessory outputs are disabled. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. It is compatible with both micro and full-sized cinema batteries. Weight: 146gDimensions: 75 x 25.6 x 108 mm
Wooden Camera WC Pro V-Mount (3x D-Tap) SKU: 257800 Wooden Camera brand Pro V-Mount plate is a metal power plate, created in partnership with Anton Bauer, and has a rugged aluminum body for durability and secure battery mounting. Features 3x D-Taps for accessory power at battery voltage (12-16V), a digital fuse with reset button, rear cover plate, and captive mounting screws. Should the user exceed the set current for accessories, only the accessory outputs are disabled leaving the camera running normally. Once the current load has been reduced by either removing accessories or reconfiguring, the reset button can be pressed to enable accessory power again. Great for use with Director's Monitor Cage or for an adjustable mount system attached to rods, use the Battery Slide or Recorder Slide paired with the appropriate Rod Clamp: Rod Clamp (15mm LW), Rod Clamp (15mm Studio), and Rod Clamp (19mm). Weight: 234g Dimensions: 142.4 mm x 90.8 mm x 21.3 mm
Wooden Camera WC Pro V-Mount BMPCC4K SKU: 265500 WC Pro V-Mount (Blackmagic Pocket Cinema Camera 4K, BMPCC4K) is a metal power plate, created in partnership with Anton Bauer, and has a rugged aluminum body for durability and secure battery mounting and a DC connector compatible with the Blackmagic Pocket Cinema Camera 4K. Features 3x D-Taps for accessory power at battery voltage (12-16V), a digital fuse with reset button, rear cover plate, and captive mounting screws. Cable exits the right side of the plate allowing neat looping and insertion into the camera. Length allows minimal cable excess while still being able to reach positions further away from the camera as necessary. For an adjustable mount system attached to rods, use the Battery Slide or Recorder Slide paired with the appropriate Rod Clamp: Rod Clamp (15mm LW), Rod Clamp (15mm Studio), and Rod Clamp (19mm). Weight: 187gDimensions: 142.6 mm x 92.1 mm x 21.9 mmCable length: 406.4mm
Wooden Camera WC V-Mount (Dual D-Tap) SKU: 191300 Wooden Camera brand V-Mount plate utilizing an IDX V-Mount. Plate provides unregulated 12V power (12-16V depending on battery connected) through 2x D-Taps on plate. Great for use with Director's Monitor Cage or combine with Battery Slide (sold separately) for adjustable battery system. Weight 234 gDimensions 142.4 mm x 90.8 mm x 21.3 mm