Pay with:
We ship with:
Fast shipping
Buy VAT exempt with your valid VAT EU ID
Purchase comfortable on account
Showroom in Warsaw +48 299 06 61

TILTA Nucleus-M Wireless Follow Focus System

TILTA Nucleus-M


The TILTA Nucleus-M is a revolutionary wireless follow focus system. Have full control of focus, iris, and zoom on Cine lenses or compatible "cine-moded" DSLR lenses. Ideal for 3-axis gimbals, shoulder mounts systems, and drone shoots.

1. The Nucleus-M is a wireless 3 Channel system.
2. Connections between the FIZ hand unit and the two hand grips to the motors are completely wireless.
3. Each motor has a built-in MDR unit, saving space and setup time.
4. A single motor can be powered directly from the camera’s battery though a 7-Pin to P-TAP cable then daisy chained via 7-Pin to 7-Pin cable to run additional motors.
5. There is no limit on the amount of motors an operator can attach per channel.
6. The FIZ hand unit and two handle grips have a wireless range of 1000 feet.
7. The signal from the FIZ hand unit can be upgraded to 1 1/4 miles with an additional accessory.
8. Both hand grips and FIZ hand unit run off (2) 18650 batteries. (Batteries are NOT included.)
9. When fully charged the batteries in the hand grips can last up to 2 days.
10. The batteries in the FIZ unit can last up to 10 hours.
11. FIZ hand unit is capable of controlling 3 channels – focus, zoom, and iris as well as overriding the hand grips.
12. 0.8 mod, 35-tooth, 32 pitch gear with a face width of 10mm
13. Motors can calibrate on lenses without hard stops – such as photo-lens with follow focus gears.
14. Motors fit standard 15mm and 19mm Rods
15. Ideal for Gimbal, Drone, and Shoulder-mounted setups

Technical data

Gunmetal Grey

Stainless Steel
ABS Plastic
Brazilian Rosewood

FIZ Hand Unit (with focus disk but no batteries): 0,44 kg
FIZ Hand Unit (with focus disk and batteries): 0,53 kg

Right Handle Grip (no batteries or adapters): 0,26 kg
Left Handle Grip (no batteries or adapters): 0,24 kg

Arri Rosette Male to Handle Grip Adapter: 0,07 kg
25mm/30mm Gimbal to Handle Grip Adapter: 0,04 kg

Motor (no rail adapter): 0,19 kg
Motor with 15mm rail adapter: 0,22 kg
Motor with 19mm rail adapter: 0,22 kg

Motor Dimensions:
Length/Height: 11,43 cm
Width: 6,98 cm (motor plus rail adapter)
Width: 6,68 cm (ports to tip of gear)
Width: 8,25 cm (end to end furthest points)
Depth: 1,60 cm (rail mount section)
Depth: 1,90 cm (base section)
Depth: 3,51 cm (motor section)

In the box

1 x Wireless FIZ Hand Unit
2 x Brushless Wireless Motors with 19mm Rod Support and 15mm Rod Bushings
1 x Wireless Handle Left (Focus)
1 x Wireless Handle Right (Iris, Zoom)
4 x Follow Focus marking disks
1 x 7-Pin to 740mm P-TAP Motor Power Cable
1 x 296mm 7-Pin to 7-Pin Straight Motor Connection Cable
1 x 180mm 7-Pin to 7-Pin Straight Motor Connection Cable
1 x 18650 4 Slot Battery Charger
2 x Handle to Arri Standard Rosette Adapter
2 x Handle to Gimbal Bar Adapter (Compatible with 25mm/30mm Diameter)
1 x Wireless FIZ Hand Unit Strap
1 x Hard Shell Waterproof Safety Case

ATTENTION! No 18650 batteries included. Nucleus-M set needs 6 x 18650

Related links of the manufacturer

Accessory Items

TILTA Nucleus-M 3-Pin to 7-Pin Run/Stop Cable
TILTA Nucleus-M 3-Pin to 7-Pin Motor Power + Arri R/S Cable SKU: RS-03-AM Compatible with any 3-pin Fischer R/S port: Arri Alexa SXT, Arri XT, Arri Amira, Arri Alexa LF Tilta 3-pin to 7-pin cable for the Nucleus-M allows you to power the motors from 3-pin power while also giving you run/stop capabilities in camera systems that support it. To power all of the motors, simply plug this cable into one of the motors and then daisy chain power to the other motors using the Nucleus-M 7-pin to 7-pin power cables. Note that this cable was specifically designed for the Nucleus-M so the R/S function only works with the Nucleus-M’s own hand unit and handles.

PLN 377.67*
net: PLN 307.05
Free shipping
TILTA Armor Man 2.0 Nucleus-M Support Cups
TILTA Armor Man 2.0 Nucleus-M Support Cups SKU: ARM-T02-SC-NM The Armor Man 2.0 Nucleus-M Support Cups allow for an easy solution to attach and detach your gimbal to the Armor Man 2.0’s mechanical arms when using the Nucleus-M’s hand grips with your gimbal system. When you want to attach the Armor Man to the gimbal, simply fit the gimbal-mounted Nucleus-M hand grips into the support cups and then re-grab the hand grips like normal to start operating. When you want to stop operating, simply dock the gimbal, grab onto the support cups and detach them from the hand grips.

PLN 985.23*
net: PLN 801.00
TILTA Nucleus-M 7-Pin to 7-Pin Motor to Motor Connection Cable
TILTA Nucleus-M 7-Pin to 7-Pin Motor to Motor Connection Cable TILTA Nucleus-M 7-pin to 7-pin power cable is used to provide a daisy-chained link between two Nucleus-M follow focus motors enabling both communication and power distribution between motors. Note that a P-tap to 7-pin or 3-pin to 7-pin cable is needed to power one of the motors first before this cable transfers power and information to another motor.

PLN 519.98*
net: PLN 422.75
PATONA Premium 18650 Cell Li-ion Battery unprotected 3,7V 3350mAh
PATONA Premium 18650 Li-ion Battery PATONA Premium 18650 Li-ion Battery is compatible with Tilta Battery for gimbal Gravity Tilta and Nucleus M. Safety instructions: Please use only chargers specified for 18650 Cells with 4.2V to charge the battery. Read the description of the 18650 charger and understand the charging method before usage. The Battery is a unprotected Flat-Top version. You should always use a protection circuit board (PCB) to Keep battery from overcharged and over-discharged. Lithium cells may only be operated with protective electronics and processed by qualified specialist personnel. Do not short-circuit and deeply discharge the batteries Technical Data Brand: PATONA Appellation: 18650 Li-Ion Type: INR18650F1L Capacity: 3350mAh Nominal voltage: 3,63V Charge voltage: 4,2V ± 0.05V Discharge voltage: 2.5V Maximum current delivery: 4875mA Maximum charge current: 1625mA Protective circuit PCB: not available Positive pole: flat (FlatTop) Diameter: 18.29 ± 0.11mm Height: ≤ 65.15mm Weight: Max. 49.0g Operating temperature: Charge 0-45°C, Discharge -20-50°CRechargeable: Yes Charging cycles: 300 Charging method: CC-CV In the box 6 x PATONA Premium 18650

PLN 268.20*
net: PLN 218.05
Free shipping
TILTA Nucleus-M Motor Kit I
TILTA Nucleus-M Motor Kit I SKU: WLC-T03-M1 This Nucleus-M motor kit allows you to add a motor to your Nucleus-M kit along with the 7-pin to 7-pin power cable that allows you to power the motor from a daisy-chained connection to another Nucleus-M motor.

PLN 1,860.99*
net: PLN 1,513.00

Similar products

Free shipping
TILTA Nucleus-Nano WLC-T04
TILTA Nucleus-Nano SKU: WLC-T04 The TILTA Nucleus-Nano is a revolutionary wireless lens control system specifically designed for handheld gimbal systems. It makes it possible for a single operator to control a lens gear while simultaneously operating their gimbal. The Nano system is compatible with all DSLR, mirrorless, and modified “cine-style” vintage photo lenses. The Nano Hand Wheel Controller has a compact knob design similar to professional follow focus hand units (the design is very similar to the Tilta Nucleus-M hand unit’s focus wheel). The Nano Hand Wheel Controller has no delay. It is highly responsive, wireless, and accurate. It is powered via a single 14500 rechargeable battery (which is included in the kit) and yields a 6 hour operating time. When used in conjunction with the Tilta Gravity G2X Handheld Gimbal, simple single-handed operation is possible by mounting the controller unit to the gimbal body’s rosette connection. Easily toggle between the G2X’s modes and pull focus at the same time! The Nucleus-Nano uses a brand new state of the art power-efficient miniature motor. The Nano Motor features low noise and high torque. It can perform super fast focus pulls with silent precision! The built-in 15mm rod adapter allows for flexibility and compatibility with a wide range of camera rigs and professional mounting solutions. The motor has a 5-18V input tolerance for power via a Micro USB port. This allows the motor’s power to be drawn from the G2X tilt motor’s 5V Micro USB output or via a P-tap to 5V Micro USB cable (sold separately). The Nano Motor has its own built-in motor drive that communicates directly with the Nano Hand Wheel Controller. This negates the need to mount a separate MDR to your rig, allowing for a more compact camera setup and a quicker setup time. Simply set the Nano Motor and Nano Hand Wheel Controller to the same channel and you will have full control. The wireless range of both the Nano Hand Wheel Controller and Nano Motor is 300 feet! The Nano Motor allows for automatic calibration of the lens as well as a manual calibration if you are using lenses that don’t have hard end stops at close focus and infinity via the ability to set A-B limits on the Nano Hand Wheel Controller. Every motor has a 0.8 mod, which is the standard gear size for most cinema lenses. The torque of the Nucleus-Nano Motor at 5.5V is 0.65N·m and at 14.8V is 1N·m The Nano Motor is also able to connect to the Nucleus-M’s FIZ hand unit and hand grips, allowing for a variety of ways to control the motor as you see fit. The kit also comes with a lightweight mounting frame for 15mm rods. The rod mounting frame is simple, reliable, strong, and streamlined. Simply connect the mounting frame to your camera or together with the G2X Series Manfrotto Style Camera Quick Release Baseplate with Riser to fit your needs. Lastly, the Nano system can provide record Run/Stop functionality for numerous camera systems. In the box 1 x Nucleus-Nano Hand Wheel Controller1 x Nucleus-Nano Wireless Follow Focus Motor1 x 15mm Single Rod Mounting Baseplate For 95mm Lens1 x 1/4″-20 Hex Screws1 x Rod Mount Hex Screw1 x 15mm x 100mm Black Aluminum Rod 1 x 31cm 5V Micro USB male to 5V Micro USB male motor power cable2 x Photographic lens follow focus gear rings1 x Nucleus-Nano Hand Wheel Attachment Plate for Ronin-S/G2x1 x Nucleus-Nano Hand Wheel Attachment Adapter for Zhiyun Crane1 x 4500 Dual Battery Wall Charger2 x 14500 Batteries1 x M4 Allen key1 x M6 Allen key1 x User Guide

PLN 1,751.52*
net: PLN 1,424.00
Pay with:
We ship with: